Peavey Triumph PAG 60 - Page 6

SPECIFICATIONS
PAG ™ 60
POWER AMP SECTION
2-6L6GC’s with 12AX7 driver
Rated Power & Load:
60 W RMS into S or 4 ohms
Power @ Clipping:
(Typically @ 5% THD, 1 kHz,
120 V AC line) 65 W RMS into
8 or 4 ohms
(Bias must be reduced
to measure)
Frequency Response:
+0, -2 dB 50 Hz to 20 kHz
@ 50 W RMS into 8 ohms
Hum & Noise:
Greater than 76 dB below
rated power
Power Consumption:
200 W, 50/60 Hz, 120 V AC
(Domestic)
PREAMP SECTION
3-12AX7’s
The following specs are measured @ 1 kHz
with the controls preset as follows:
Low & High EQ @ 10, Mid EQ
@ 0, Bright Out
Ultra & Crunch Posts @ 10,
Gain switches out
Bottom, Body, & Edge @ 0 dB
Reverb level @ 0, Master level
@ 10
(Nominal levels are with Pre
Gains @ 5)
(Minimum levels are with Pre
Gains @ 10)
Preamp High Gain Input:
Impedance: Very high Z,
470 K ohm
Ultra Channel:
(with channel-select in)
Nominal Input Level: -46 dBV,
5 mV RMS
Minimum Input Level: -64 dBV,
0.6 mV RMS
(Subtract 15 dB with gain
switch in)
Crunch Channel:
(footswitch selected)
Nominal Input Level: -34 dBV,
20 mV RMS
Minimum Input Level: -52 dBV,
2.5 mV RMS
(Subtract 15 dB with gain
switch in)
Clean Channel:
(with channel-select out)
Nominal Input Level: -16 dBV,
150 mV RMS
Minimum Input Level: -34 dBV,
20 mV RMS
Maximum Input Level: 0 dBV,
1.0 V RMS
Preamp Low Gain Input:
(-6 dB Pad)
Impedance: High Z, 44 K ohms
All levels increased by +6 dB
Effects Send:
Load Impedance: 47 K ohms
or greater
Nominal Output: -10 dBV,
300 mV RMS
Effects Return:
Impedance: Very high Z,
470 K ohm
Designed Level: -10 dBV,
300 mV RMS
Preamp Output:
Load Impedance: 47 K ohms
or greater
Nominal Output: +10 dBV,
3 V RMS
Remote Footswitch:
Special 3 button unit with LED
indicators (supplied)
System Hum & Noise @
Nominal Level:
(Clean Channel)
(20 Hz to 20 kHz unweighted)
Greater than 74 dB below rated
power (Special noise gate
circuitry for Ultra & Crunch)
Equalization:
(clean channel only)
Custom Low, Mid, & High
passive type EQ
Push Bright: +6 dB @ 2 kHz
Voicing: (Ultra and Crunch
channels only)
Active Bottom, Body, and
Edge EQ
Push Gain: Increases gain in
Ultra and Crunch channels.
PAG ™ 120
POWER AMP SECTION
4-6L6GC’s with 12AX7 driver
Rated Power & Load:
120 W RMS into 8 or 4 ohms
Power @ Clipping:
(Typically @ 5°/o THD, 1 kHz,
120 V AC line) 130 W RMS into
8 or 4 ohms
(Bias must be reduced
to measure)
Frequency Response:
+0, -2 dB 50 Hz to 20 kHz
@ 100 W RMS into 8 ohms
Hum & Noise:
Greater than 76 dB below
rated power
Power Consumption:
400 W, 50/60 Hz, 120 V AC
PREAMP SECTION
3-12AX7’s
The follwoing specs are measured @ 1 kHz
with the controls preset as follows:
Low & High EQ @ 10, Mid EQ
@ 0, Bright out
Ultra & Crunch Posts @ 10,
Gain switches out
Bottom, Body, & Edge @ 0 dB
Reverb level @ 0, Master level
@ 10
(Nominal levels are with Pre
Gains @ 5)
(Minimum levels are with Pre
Gains @ 10)