Peavey ValveKing 20 - Page 28

Specifications
ValveKing
®
100
Rated Power: 100 W (rms) into 4, 8 or 16Ω
Power Consumption: (Domestic) 275 W, 50/60
Hz, 120 VAC
Tube Complement: 4 x 6L6GC, 3 x 12AX7/ECC83
Dimensions (HxWxD): 9.75" x 26.50" x 11.13" /
248 mm x 673 mm x 283 mm
Weight: 38 lbs / 17 kg
ValveKing
®
50
Rated Power: 50 W (rms) into 4, 8 or 16Ω
Power Consumption: (Domestic) 160 W, 50/60
Hz, 120 VAC
Tube Complement: 2 x 6L6GC, 3 x 12AX7/ECC83
Dimensions (HxWxD): 20.50" x 22.00" x 10.2 /
521 mm x 559 mm x 260 mm
Weight: 40.6 lbs / 18 kg
ValveKing
®
20
Rated Power: 20 W (rms) into 4, 8 or 16Ω
Power Consumption: (Domestic) 90 W, 50/60
Hz, 120 VAC
Tube Complement: 2 x EL84, 3 x 12AX7/ECC83
Dimensions (HxWxD): 20.50" x 22.00" x 10.25"
/ 521 mm x 559 mm x 260 mm
Weight: 37.6 lbs / 17 kg
ValveKing
®
20MH
Rated Power: 20 W (rms) into 8 or 16Ω
Power Consumption: (Domestic) 90 W, 50/60
Hz, 120 VAC
Tube Complement: 2 x EL84, 3 x 12AX7/ECC83
Dimensions (HxWxD): 7.25" x 14.00" x 7.75 /
184 mm x 356 mm x 197 mm
Weight: 14.6 lbs / 7 kg
ValveKing
®
Series 100/50/20/20MH Preamp
Specifications
Preamp High Gain Input:
Impedance: Very High-Z, 1MΩ
Preamp Low Gain Input:
(-10 dB Pad)
Impedance: High-Z, 68 kΩ
Effects Send:
Low Impedance: High-Z, 22 kΩ or greater
Nominal Output Level: 0 dBV,
1.0 V (rms)
Effects Return:
Impedance: Very High-Z, 1 MΩ
Designed Input Level: 0 dBV,
1.0 V (rms)
Equalization: (Clean channel only)
Custom Low, Mid, & High passive EQ
Push Bright: +6dB @ ~3.5kHz
Equalization: (Lead channel and 20MH)
Custom Low, Mid, & High passive EQ
Lead Channel Front Panel Footswitch Functions:
Push Gain: Increase Gain in Lead channel and
introduces a tighter low end response.
Push Volume: +3-5dB Volume boost
(more effect at midway Lead Volume settings)
Remote Footswitch (s): (optional)
One or two dual latching footswitches.
One footswitch for channel selection and
Volume Boost and/or Gain Boost functions
preset on the front panel GAIN (8) and VOLUME
(9) switches described earlier.
A second footswitch can be used for switching
REVERB and EFFECTS LOOP on and off.
Other Misc Specifications
Signal to Noise Ratio:
Better than 74dB on all models (compared to
full power)
MSDI
™
Output:
Low Impedance: 600Ω Balanced
Output Level: Dependent on controls but -12dBu
(+/-3dBu) at full power on all models
USB Output:
Output Level: Dependent on controls but -6dB
(+/-3dB) at full power on all models
Power attenuator:
Three setting switch for 100% (bypassed), 25%
and 5% of rated power
Headphone Output: (20MH only)
Stereo mini-jack with filtered output for driving
stereo headphones, 16Ω - 50Ω impedance per
channel.
Features and specifications subject to change
without notice.