Pelican PC1000 - User Manual

Other manuals for Pelican PC1000

Installation Guide19 pages

Questions and Answers

E
Edward JonesAug 16, 2025
Why is the water inside my house gray after installing Pelican Water Filtration Systems?
- A
  Aaron RiddleAug 16, 2025
  If you notice gray water inside your house after installing Pelican Water Filtration Systems, don't worry. This is a common occurrence with all carbon filters and should gradually disappear. The carbon inside the tank might still have air pockets. When these pockets release, they can turn the water slightly gray due to carbon dust. Rest assured, this carbon dust is harmless.
T
Theresa BrownAug 19, 2025
What to do if the water pressure is slowing with my Pelican Water Filtration Systems?
- M
  Mitchell BeckerAug 19, 2025
  If the water pressure of your Pelican Water Filtration Systems is slowing, it's advisable to replace the Sediment Filter every 6-9 months, depending on the amount of sediment in your water supply. If the system's pressure is slowing, inspect the Sediment Filter and replace it if needed.
Z
zcabreraAug 22, 2025
How to fix pressure dropping during carbon wash in Pelican Water Filtration Systems?
- J
  jerry16Aug 22, 2025
  If the pressure is dropping off during the carbon wash for your Pelican Water Filtration Systems, it's likely due to trapped air in the carbon bed. To resolve this, turn off the water supply and allow the tank to sit for about 30 minutes. This will give the carbon time to settle away from the basket inside the tank. If the pressure drops again, let the system stand for 72 hours, then slowly turn the water supply back on to continue the carbon wash.
R
Ryan MooreAug 26, 2025
What to do if there is water leaking at the top of the tank around the head of my Pelican Water Filtration Systems?
- M
  Michael ZhangAug 26, 2025
  If you notice water leaking at the top of the tank around the head of your Pelican Water Filtration Systems, try tightening the head. The tank head comes pre-installed hand-tight, so just turn it snug, being careful not to over-tighten it.
T
Tina GillespieAug 28, 2025
How to level a leaning tank in Pelican Water Filtration Systems?
- W
  williamskellyAug 28, 2025
  If the tank leans to one side or isn't level for your Pelican Water Filtration Systems, lift the tank and drop it on the ground until it stands vertically. The tank's bottom is round, and the boot is designed to help the tank stand upright.
M
matthewrasmussenAug 31, 2025
What to do if water pressure is slowing immediately after installing Pelican PC1000 Water Dispenser?
- J
  Jasmine MayoAug 31, 2025
  If you experience a slowdown in water pressure immediately after installing your Pelican Water Dispenser, avoid using high flow rates from sources like bathtubs, utility sinks, hose bibs, multi-headed showers, or body sprayers for the first 72 hours. If you suspect a carbon blockage in the top basket due to high flow within this period, turn off all running water for at least 10 minutes to clear the blockage. After this, you can resume using water at low or normal flow rates.
T
timothy74Sep 3, 2025
Why is the water pressure slowing in my Pelican Water Dispenser?
- D
  Dennis KaneSep 3, 2025
  A decrease in water pressure indicates that the Sediment Filter may need replacing. It's generally recommended to replace the Sediment Filter every 6-9 months, depending on the sediment amount in your water supply. Inspect the Sediment Filter and replace it if necessary.
C
Charles GriffinSep 6, 2025
Why does the water appear grey or cloudy in my Pelican PC1000 Water Dispenser?
- J
  jsmithSep 6, 2025
  For the first seven to ten days after installation, the water may appear grey or cloudy due to extra carbon dust.
J
Jeff SmithSep 8, 2025
How to fix Pelican Water Dispenser that leans to one side?
- S
  Sylvia BriggsSep 9, 2025
  If your Pelican Water Dispenser tank isn't level, lift it straight up about 6 inches and gently tap it on the ground until it stands vertically. The tank's round bottom and the boot are designed to allow it to stand upright.
S
Stephanie GarrettSep 12, 2025
How to fix water leaking at the top of Pelican PC1000 Water Dispenser?
- B
  Bryan MckenzieSep 12, 2025
  You may need to turn the head to tighten it. The tank head is pre-installed hand-tight, do not overtighten the head (just turn it snug).