ICS –Quick reference card
V4.10 dd 12-11-2015
For additional information see manual: OM_xx_ICS_OnBoard_Configuration (xx = Language code)
1 of 2
General Settings
User weight
Entry: Button 2 and 4
(all led’s green
– led 7 off / led 8 flashes red)
Setting: Button 1 or 5
Save: Button 8 (2 sec)
0-50 kg / 0-110 lb
121-135 kg / 266-300 lb
51-75 kg / 111-165 lb
136-160 kg / 301-350 lb
76-100 kg / 166-220 lb
161-180 kg / 351-400 lb
101-120 kg / 121-265 lb
181-200 kg / 401-450 lb
LED indication level
Entry: Button 2 and 4
(all led’s green –
led 7 off / led 8 flashes red)
Setting: Button 3 or 7
Save: Button 8 (2 sec)
Level 1 All LEDs off. No indications. (Use with “single page” layouts.)
Level 2 Only displays Green LEDs No indication of Drive Speed or Actuator Limits.
Level 3 Only displays Solid LEDs No indication of Actuator Limits (Only Drive Speed.)
Level 4 All Indications Displayed (Default Setting)
NOTE: Flashing RED LEDs (Actuator Errors) are displayed in every Indication Level.
Switch box Layout
Entry: Button 1 and 3
(all led’s green
– led 7 flashes green
/led 8 cont. red)
Setting: Button 1 or 5
Save: Button 8 (2 sec)
Note:
*1
Only for CorpusVS
/ Corpus3G
1
A
A D
J
2
B
B
E
K
3
C C F
4
D D G
5
E M
6
F
7
G
*1
L
12
L
Other General Setting
Entry: Button 2, 7 and 8
(all led’s green –
led 7 and 8 toggle green)
Next page: Button 4
Prev. page: Button 8
Page 1: Led 7 and 8
toggle green
Page 2: Led 7 flashes green
and Led 8 Off
Page 3: Led 7 cont. green
and Led 8 Off
Save: No action required
Setting:
Green Red
1 1 1 Actuators blocked while driving Actuators enabled while driving
1 2 5 Low backrest installed (C3G) Standard (High) backrest installed
1 3 2 -5 Tilt adapter installed No -5 Tilt adapter installed
1 4 6 Pause tilt at 0º No pause Tilt at 0º
1 5 3 Leg rest pauses before reducing speed Leg rest does not pauses before reducing speed
1 6 7 Enable IRM (Independent Repositioning Mode) Disable IRM (Independent Repositioning Mode)
2 1 1 Push leg rest on Push leg rest off
2 2 5 Push back on Push back off
2 3 2 Invert Elevator: up is rear button Invert Elevator: up is front button
2 4 6 Invert Tilt: forward is rear button Invert Tilt: forward is front button
2 5 3 Invert Backrest: forward is rear button Invert Backrest: forward is front button
2 6 7 Invert Leg rest: up is rear button Invert Leg rest: down is front button
3 1 1 Leg rest linked to backrest Leg rest NOT linked to backrest
Corpus II seat
Legrest angle for ¼ speed
(rear-/mid-wheel driven chairs)
Entry: Button 1, 2 and 7
(all led’s green – led 7 flashes red
/led 8 flashes green)
Setting: Button 1 or 5
Save: Button 8 (2 sec)
3º
15º
6º
18º
9º
21º
12º
Corpus 3G/HD/APE/VS
Seat depth
Entry: Button 3, 4 and 6
(all led’s green – led 7 flashes green
/led 8 flashes red)
Setting: Button 1 or 5
Save: Button 8 (2 sec)
470mm/18”
545mm/21”
620mm/24”
495mm/19”
570mm/22”
520mm/20”
595mm/23”
Legrest angle offset for ¼ speed
(rear-/mid-wheel driven chairs)
Entry: Button 1, 2 and 7
(all leds green – led 7 flashes red
/led 8 flashes green)
Setting: Button 1 or 5
Save: Button 8 (2 s
ec)
+12º
+3º
-6º
+9º
0º
-9º
+=6º
-3º
-12º
IRM position (Corpus 3G/HD/APE/VS)
Independent Repositioning Mode is
using/replacing Memory 3
Note: IRM needs to be enable (see above: Other
General Settings)
Entry: Button 5 and 7
(all led’s green – led 8 flashes red/green)
Extra step for Corpus APE and Corpus VS only:
- Press button 7. (Led 7 will lit solid green)
Setting backwards position:
Button 1 or 5 Tilt
Button 2 or 6 Legrest
Button 3 or 7 Backrest
Save: Button 4
Setting forwards position:
Button 1 or 5 Tilt
Button 2 or 6 Legrest
Button 3 or 7 Backrest
Save: Button 8
General
To Next Page
