To Next Page
N
Norman FernandezSep 23, 2025
What to do if my Permobil Wheelchair shows a Joystick Error?
- Jjason40Sep 23, 2025
Ensure that the joystick is in the central position and start up the control system.
What to do if my Permobil Wheelchair shows a Joystick Error?
Ensure that the joystick is in the central position and start up the control system.
What does High Battery mean on my Permobil Wheelchair?
If the control system detects that the battery voltage is higher than 35 V, this can cause a high battery message. Check the batteries and their connection to the control system.
What does Brake Error mean on Permobil Wheelchair?
If the control system detects a problem in the solenoid brakes or the connections to them, this will cause a brake error. Check the solenoid brakes, their cables, and the connections to the control system.
Why my Permobil M300 cannot be charged?
If your Permobil Wheelchair cannot be charged, the main fuse might be blown. Check possible causes carefully before resetting or replacing the main fuse.
What to do if Permobil Wheelchair does not start?
If your Permobil Wheelchair doesn't start, there are several potential causes. First, the batteries may be discharged, so try charging them. Also, check the cable connection to the control panel and ensure it is securely attached. Finally, verify the Circuit Breaker is not in the ”OFF” position.
What does Module Error mean on Permobil M300 Wheelchair?
If the control system detects an error in a specific module, this will cause a module error. Check all cables and connections.
What does Bad Settings mean on Permobil M300?
If the control system detects incorrect or invalid program settings, this will cause bad settings. Check all parameter settings and then reprogram the control system with the help of R-net’s PC programmers.
What does Bad Cable mean on Permobil Wheelchair?
If the control system detects a connection error in the communication cables between the modules, this will cause a bad cable message. Check all cables and connections to ensure there is no stoppage.
Why does my Permobil M300 switch off by itself?
If your Permobil Wheelchair switches off after inactivity, the electronics' energy-saving mode has been activated. To resolve this, switch the wheelchair on again using the start key on the control panel.
Why is my Permobil M300 Wheelchair driving at reduced speed?
If your Permobil Wheelchair can only be driven at reduced speed, it might be because the seat lift is raised too high. Try lowering the seat lift.
Contact Permobil Inc. USA for technical issues.
Order spare parts through your dealer.
Contact dealer or Permobil Inc. USA for warranty details.
Refer to the Owner's Manual for maintenance procedures.
Location of the chassis identification number.
ID numbers for R-net power module and control panel.
ID numbers for VR2 power module, control panel, and lights module.
Steps to remove and install front and rear chassis covers.
Steps to remove and fit the upper chassis cover.
Steps to remove and install link arm covers.
Steps to remove and install drive motor covers.
Procedure for replacing the front battery.
Procedure for replacing the rear battery.
Steps to remove and re-attach drive wheels.
Procedure for taking apart the rim and fitting tires.
Steps to remove and re-attach caster wheels.
Procedure for fitting solid tires to caster rims.
Steps to remove and re-install shock absorbers.
Adjusting spring force based on user weight for optimal performance.
Steps to remove and re-install rear link arms.
Steps to remove and re-install front link arms.
Steps to remove and re-install wheel forks.
Steps to remove and re-install friction brakes.
Steps to remove and re-install the drive motor.
Steps to remove and re-install magnetic brakes.
Procedure for manually raising or lowering the seat lift.
Steps to remove and re-install the electric seat lift.
Setting the seat tube to service position and adjusting seat height.
Steps to remove and re-install the fixed seat tube.
Steps to remove and re-install the seat support.
Fitting and adjusting the rubber cushion and its bracket.
Steps to remove and re-install the Corpus 3G seat.
Steps to remove and re-install PS seat without angle mechanism.
Steps to remove and re-install PS seat with angle mechanism.
Steps to remove and re-install the R-net control panel.
Steps to remove and re-install the VR2 control panel.
Steps to remove and re-install the R-net power module.
Steps to remove and re-install the VR2 power module.
Steps to remove and re-install the ICS master module.
Steps to remove and re-install the lights module.
Procedures for resetting and removing the main fuse.
Procedure for installing a new main fuse.
Steps for removing and installing front lights and indicators.
Steps for removing and installing rear lights and indicators.
Explanation of the wheelchair's programmable control system.
Guide to common faults and remedies for the R-net control system.
Understanding R-net diagnostic screens and error indicators.
Accessing the system log and definitions of diagnostic messages.
Performing basic inspection, brake, test run, and gradient tests.
Guide to common faults and remedies for the VR2 control system.
Understanding VR2 battery voltage indicator and fault detection.
Interpreting VR2 error signals and applying remedies.
Wiring diagram for the R-net control system components.
Wiring diagram for the VR2 control system components.
General| Weight Capacity | 300 lbs |
|---|---|
| Drive System | Mid-wheel drive |
| Turning Radius | 20.5 inches |
| Caster Wheels | 8 inches |
| Overall Width | 24 inches |
| Battery Type | Gel |
