Why does my Permobil Wheelchair show a Low Battery error?
If the control system detects that the battery voltage is lower than 16 V, this can cause a low battery message. Check the batteries and their connection to the control system.
Why is my Permobil M300 Wheelchair driving at reduced speed?
If your Permobil Wheelchair can only be driven at reduced speed, it might be because the seat lift is raised too high. Try lowering the seat lift.
What to do if my Permobil Wheelchair cannot be driven?
If your Permobil Wheelchair cannot be driven, it might be due to several reasons. First, if the battery charger is connected, stop charging and disconnect the charging cable. Second, the brake release might be activated; reset the brake release. The wheelchair could also be locked, so unlock it. Finally, ensure that the magnetic brakes are engaged.
How to fix Permobil Wheelchair that will not start?
If your Permobil Wheelchair won't start, the batteries might be discharged. Try charging the batteries. Also, check the cable connection to the control panel and ensure it's properly inserted. Finally, the main fuse might be blown; carefully check for possible causes before resetting or replacing it.
What to do if Permobil M300 stops while being driven?
If your Permobil Wheelchair suddenly stops while you're driving, a possible cause is a loose cable connection to the control panel. Ensure the cable is securely attached. Another potential reason is a triggered Circuit Breaker.
Why Permobil Wheelchair can not be driven?
If your Permobil Wheelchair can't be driven, it might be due to a few reasons. Check if the battery charger is connected and terminate charging by removing the charging cable. Another reason might be that the Wheel Locks are activated, so reset them.
What to do if Permobil Wheelchair does not start?
If your Permobil Wheelchair doesn't start, there are several potential causes. First, the batteries may be discharged, so try charging them. Also, check the cable connection to the control panel and ensure it is securely attached. Finally, verify the Circuit Breaker is not in the ”OFF” position.
Why my Permobil M300 cannot be charged?
If your Permobil Wheelchair cannot be charged, the main fuse might be blown. Check possible causes carefully before resetting or replacing the main fuse.
What does Brake Error mean on Permobil Wheelchair?
If the control system detects a problem in the solenoid brakes or the connections to them, this will cause a brake error. Check the solenoid brakes, their cables, and the connections to the control system.
What does High Battery mean on my Permobil Wheelchair?
If the control system detects that the battery voltage is higher than 35 V, this can cause a high battery message. Check the batteries and their connection to the control system.
General| Weight Capacity | 300 lbs |
|---|---|
| Drive System | Mid-wheel drive |
| Turning Radius | 20.5 inches |
| Caster Wheels | 8 inches |
| Overall Width | 24 inches |
| Battery Type | Gel |
Contact Permobil Inc. USA for technical issues.
Order spare parts through your dealer.
Contact dealer or Permobil Inc. USA for warranty details.
Refer to the Owner's Manual for maintenance procedures.
Location of the chassis identification number.
ID numbers for R-net power module and control panel.
ID numbers for VR2 power module, control panel, and lights module.
Steps to remove and install front and rear chassis covers.
Steps to remove and fit the upper chassis cover.
Steps to remove and install link arm covers.
Steps to remove and install drive motor covers.
Procedure for replacing the front battery.
Procedure for replacing the rear battery.
Steps to remove and re-attach drive wheels.
Procedure for taking apart the rim and fitting tires.
Steps to remove and re-attach caster wheels.
Procedure for fitting solid tires to caster rims.
Steps to remove and re-install shock absorbers.
Adjusting spring force based on user weight for optimal performance.
Steps to remove and re-install rear link arms.
Steps to remove and re-install front link arms.
Steps to remove and re-install wheel forks.
Steps to remove and re-install friction brakes.
Steps to remove and re-install the drive motor.
Steps to remove and re-install magnetic brakes.
Procedure for manually raising or lowering the seat lift.
Steps to remove and re-install the electric seat lift.
Setting the seat tube to service position and adjusting seat height.
Steps to remove and re-install the fixed seat tube.
Steps to remove and re-install the seat support.
Fitting and adjusting the rubber cushion and its bracket.
Steps to remove and re-install the Corpus 3G seat.
Steps to remove and re-install PS seat without angle mechanism.
Steps to remove and re-install PS seat with angle mechanism.
Steps to remove and re-install the R-net control panel.
Steps to remove and re-install the VR2 control panel.
Steps to remove and re-install the R-net power module.
Steps to remove and re-install the VR2 power module.
Steps to remove and re-install the ICS master module.
Steps to remove and re-install the lights module.
Procedures for resetting and removing the main fuse.
Procedure for installing a new main fuse.
Steps for removing and installing front lights and indicators.
Steps for removing and installing rear lights and indicators.
Explanation of the wheelchair's programmable control system.
Guide to common faults and remedies for the R-net control system.
Understanding R-net diagnostic screens and error indicators.
Accessing the system log and definitions of diagnostic messages.
Performing basic inspection, brake, test run, and gradient tests.
Guide to common faults and remedies for the VR2 control system.
Understanding VR2 battery voltage indicator and fault detection.
Interpreting VR2 error signals and applying remedies.
Wiring diagram for the R-net control system components.
Wiring diagram for the VR2 control system components.
To Next Page
