1:8
Introduction
Presser feet
6WDQGDUGSUHVVHUIRRW$ZLWK,'7DWWDFKHGRQWKHPDFKLQHXSRQGHOLYHU\
This foot is used mainly for straight stitching and zigzag stitching with a stitch length
longer than 1.0 mm.
)DQF\VWLWFKIRRW$ZLWK,'7
7KLVIRRWLVXVHGIRUGHFRUDWLYHVWLWFKHV7KHJURRYHRQWKHXQGHUVLGHRIWKHIRRWLV
GHVLJQHGWRÁRZVPRRWKO\RYHUWKHVWLWFKHV
)DQF\VWLWFKIRRW$
:KHQVHZLQJGHFRUDWLYHVWLWFKHVRUVKRUW]LJ]DJVWLWFKHVDQGRWKHUXWLOLW\VWLWFKHVZLWK
OHVVWKDQPPVWLWFKOHQJWKXVHWKLVIRRW7KHJURRYHRQWKHXQGHUVLGHRIWKHIRRWLV
GHVLJQHGWRÁRZVPRRWKO\RYHUWKHVWLWFKHV
%OLQGKHPIRRWZLWK,'7
This foot is used for blindhem stitches. The toe on the foot guides the fabric. The red
guide on the foot is designed to ride along the fold of the hem edge.
=LSSHUIRRWZLWK,'7
This foot can be snapped on either the right or the left of the needle, making it easy to
VHZFORVHWRERWKVLGHVRIWKH]LSSHUWHHWK0RYHWKHQHHGOHSRVLWLRQWRWKHULJKWRUOHIWWR
sew closer to zipper teeth.
6HQVRUPDWLFEXWWRQKROHIRRW$
When connected to the machine, the buttonhole is sewn in a suitable length to the button
size that has been entered into the machine.
Manual buttonhole foot 5M
This foot is used for sewing manual buttonholes. Use the markings on the foot to position
WKHJDUPHQWHGJH7KHÀQJHURQWKHEDFNRIWKHIRRWKROGVFRUGLQJIRUFRUGHGEXWWRQKROH
6HQVRUPDWLFIUHHPRWLRQIRRW$
This foot is used for sensormatic free-motion sewing. This foot can also be used for
darning.
µTXLOWLQJIRRWZLWK,'7
7KLVIRRWLVSHUIHFWIRUSLHFLQJDQGSDWFKZRUNHVSHFLDOO\ZKHQXVHGLQFRQMXQFWLRQZLWK
the straight stitch needle plate. The clearance between the needle and the outer edge of
WKHWRHLVµPPDQGEHWZHHQWKHQHHGOHDQGWKHLQQHUHGJHRIWKHWRHµPP
)UHHPRWLRQ'DUQLQJIRRW
Insert the pin of the foot as far as it will go into the hole at the back of the presser foot
KROGHU7KHµ&VKDSHGµJXLGHVKRXOGEHSRVLWLRQHGDURXQGWKHSUHVVHUIRRWEDU7KHORQJ
arm must be behind the needle bar. Tighten the screw.
Important: Make sure that the IDT™ is disengaged when using presser foot 2A, 5A, 5M, 6A and
the free-motion/darning foot.
To Next Page
Loading...
Need help?
General
