EasyManua.ls Logo

Pfister Sonterra LF-WL2-45 User Manual

Pfister Sonterra LF-WL2-45
6 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Installation Support • Soporte de Instalación • Support dInstallation
Installation Videos Available
Videos de instalación a disposición
Vidéos d’installation disponibles
Personal Assistance, Product Specs, &
“How-to” Questions:
Asistencia personal, especificaciones del
producto y preguntas sobre “cómo hacerlo”:
Aide personnelle, spécifications du produit
et questions « pratico-pratiques » :
1800PFAUCET (7328238)
pisterfaucets.com/support
pisterfaucets.com/videos
Dec 11, 2019
Required Tools
Herramientas necesarias
Outils nécessaires
Additional Helpful Tools
Otras herramientas útiles
Outils supplémentaires utiles
Parts in the Box
Piezas en la caja
Pièces dans la boîte
Copyright © 2019, Pister Inc.
4" Centerset Lavatory Faucet
Grifo central de 4 pulg. para el baño
Robinet pou lavabo centré de 4 po.
Quick Installation Guide
Guía de Instalación Rápida
Guide dInstallation Rapide
Adjustable Wrench
Llave ajustable
Clé à mollette
Safety Goggles
Gafas de seguridad
Lunettes de sûreté
Plumber’s Putty
Masilla para plomeria
Mastic de plombier
Flashlight
Linterna
Lampe De Poche
Cloth
Paño
Chion
475060400
WARNING / AVERTENCIA / AVERTISSEMENT
To reduce the risk of injury or property damage, read all instructions before installing product. Wear safety goggles. Product must be installed in
accordance with all state & local plumbing & building codes. Call a professional if you are uncertain about installing this product.
Para disminuir el riesgo de lesiones o daños a la propiedad, lea todas las instrucciones antes de instalar el producto. Utilice gafas de seguridad. El producto
deberá instalarse de acuerdo con la normativa de plomería y construcción estatal y local. Llame a un profesional si no está seguro sobre cómo instalar este
producto.
Pour réduire le risque de blessures ou de dommages, lire toutes les instructions avant d’installer le produit. Porter des lunettes de sécurité. Le produit doit
être installé en conformité avec tous les codes de construction et de plomberie locaux et de l'état. Appelez un professionnel si vous nêtes pas certain de la
façon d’installer ce produit.
Locate water supply inlets and shut of the water supply valves. These are usually
found under the sink or near the water meter. If you are replacing an existing faucet,
remove the old faucet from the sink and clean the sink surface thoroughly.
Ubique las entradas del suministro de agua y cierre las válvulas de suministro de agua.
Generalmente se encuentran debajo del fregadero o cerca del medidor de agua. Si se trata de
un reemplazo de grifo, quite el grifo viejo y limpie completamente la supericie del fregadero.
Recherchez les entrées d'approvisionnement et fermer leurs robinets. Ces robinets se
trouvent généralement sous l'évier ou près du compteur d’eau. Si vous remplacez un robinet
existant, retirez, le vieux robinet de l'évier et nettoyer soigneusement la surface de ce dernier.
Turn O Water Supply Cierre el suministro de agua Couper l’alimentation en eau
Cold
Fría
Froid
1
Sonterra™
LF-WL2-45
A CB
D
1256832
Hot
Caliente
Chaud
SAMPLE COPY
Question and Answer IconNeed help?

Do you have a question about the Pfister Sonterra LF-WL2-45 and is the answer not in the manual?

Pfister Sonterra LF-WL2-45 Specifications

General IconGeneral
BrandPfister
ModelSonterra LF-WL2-45
CategoryPlumbing Product
LanguageEnglish

Summary

General Safety Warnings

Required Tools for Installation

Adjustable Wrench

Tool required for tightening connections during faucet installation.

Plumber's Putty

Material used to seal joints and prevent leaks around the faucet base.

Safety Goggles

Protective eyewear recommended for installation to prevent eye injury.

Cloth

Used for cleaning surfaces or wiping excess materials.

Optional Helpful Tools

Flashlight

Provides illumination for working in dimly lit areas under the sink.

Included Parts Identification

Step 1: Turn Off Water Supply

Step 2: Install Faucet Base and Body

2A Disassemble and Prepare Components

Disassemble faucet components for proper installation sequence.

2B Apply Plumber's Putty and Position Plate

Apply putty to the gasket plate and place it onto the sink surface.

Step 3: Secure Faucet Assembly

Step 4: Connect Water Supply Lines

Important Note on Supply Lines

Supply lines are not included; consult manufacturer for proper installation methods.

Step 5: Install Push & Seal Drain

5A Disassemble Pop-Up Drain Components

Disassemble the pop-up drain assembly into its individual parts.

5B/5C Drain Installation Instructions

Instructions for partially threading drain body and avoiding plumber's putty.

5D/5E Connect and Tighten Drain Nut

Connect the drain to the plumbing and securely hand-tighten the nut.

Step 6: Turn On Water & Confirm Proper Installation

6A Remove Aerator

Remove the aerator before turning on the water supply.

6B Turn On Water Supply

Open the hot and cold water supply valves to the faucet.

6C Turn On Faucet

Slowly open the faucet handles to allow water flow and check for leaks.

6D Reinstall Aerator

Reinstall the aerator after confirming proper installation and no leaks.

Related product manuals