Philips AZ1065 - Recording and Tape Deck Maintenance; Tape Recording Guidelines; Radio Recording and Maintenance

PCS 107 117
3-5
INSTRUCTONS FOR USE
Recording from the radio 1. Tune to the desired radio station (see Tuning to radio
stations).
2. Press STOP•OPEN 9/ to open the cassette door. 3. Insert a suitable cassette into the cassette deck and close the
cassette door.
4. Press RECORD 0 to start recording. 5. For brief interruptions, press PAUSE ;. To resume recording,
press PAUSE ; again.
6. To stop recording, press STOP•OPEN 9/. Tape deck maintenance To ensure quality recording and playback of the tape deck, clean parts A,B and C shown in the diagram below, after approx. 50 hours of operation, or on average once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1. Open the cassette holder by pressing STOP•OPEN 9/.
2. Press PLAY 1 and clean the rubber pressure rollers C. 3. Press PAUSE ; and clean the magnetic heads A and also the
capstan B .
4. After cleaning, press STOP•OPEN 9/.
Note: Cleaning of the heads can also be done by playing a
cleaning cassette through once.
A A B C
Environmental information All unnecessary packaging material has been omitted. We have done our utmost to make the packaging easy to separate into three materials: cardboard (box), expandable polystyrene (buffer), polyethylene (bags, protective foam). Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, exhausted batteries and old equipment.
SHUFF
LE
A
LL
REC
ORD
PLA
Y
SE
AR
CH
S
T
OP-OPEN
P
AUS
E
DB
B
WER
TU
NER
BASS BOOST
CD
T
APE
OFF
AZ
1065
CD RADIO CASSETTE RECORDER
CD
REMOTE
SENSOR
GENERAL INFORMATION ON RECORDING
• Recording is permissible insofar as copyright or other rights of
third parties are not infringed.
• This deck is not suitable for recording on CHROME (IEC II) or
METAL (IEC IV) type cassettes. For recording, use only NORMAL type cassettes (IEC I) on which the tabs have not been broken.
• The best recording level is set automatically. Altering the
VOLUME and DBB controls will not affect the recording in progress.
• At the very beginning and end of the tape, no recording will
take place during the 7 seconds, when the leader tape passes the recorder heads.
• To protect a tape from accidental erasure, have the tape in
front of you and break out the left tab. Recording on this side is no longer possible. To record over this side again, cover the tabs with a piece of adhesive tape.
SYNCHRO START CD RECORDING
1. Select CD source. 2. Insert a CD and if desired, programme track numbers. 3. Press STOP•OPEN 9/ to open the cassette door. 4. Insert a suitable cassette into the cassette deck and close the
cassette door.
5. Press RECORD 0 to start recording. – Playing of the CD programme starts automatically from the
beginning of the programme. It is not necessary to start the CD player separately.
To select and record a particular passage • Press SEARCH ∞ or §. When you recognize the passage you
want, release SEARCH controls.
• To interrupt CD playback press PLAY/PAUSE 2; (on the
remote control 2;).
– Recording will begin from this exact point in the track when
you press RECORD 0.
6. For brief interruptions during recording, press PAUSE ;. To
resume recording, press PAUSE ; again.
7. To stop recording, press STOP•OPEN 9/.
1
REC
ORD
PLA
Y
SE
AR
CH
ST
OP-OPEN
P
AUS
E
DB
B
POWE
R
TUNER
DYNAMIC BASS BOOST
CD
T
APE
OFF
AZ
10
65
CD RADIO CASSETTE RECORDER
SHUF
FLE
A
LL
V
OLUME
PROG.
B
A
T
T
LO
W
MODE
T
A
PE
TUN
ER
CD
ST
OP
PLA
Y
•
P
A
USE
SE
ARCH
•
•
•
•
•
•
S
EA
RCH
D
IGIT
AL
BA
SENSO
R