EN 115
3139 785 31532
5.
Firmware Upgrading & Diagnostic Software
5.4 DVD Module Error code
With DSW command 910 the set software can retrieve an
overview of all occurred engine errors.
5.4.1 Momentary Errors
Byte 0: latest error:
Overview of the BE error codes.
error
code
error meaning
0x00 no_error No error has occurred
0x01 illegal_command_error Command not allowed in this
state or unknown command
0x02 illegal_parameter_error Parameter(s) not valid for this
command
0x03 command_timeout_error The maximum execution time for
the command has exceeded
0x04 sledge_home_error The sledge could not be moved
home
0x05 sledge_calibration_error An error occurred during calibra-
tion of the sledge
0x06 sledge_unstable_error The sledge detected unstable
control
0x07 speed_timeout_error Spindle motor could not reach its
target speed within timeout
0x08 speed_window_error Measured spinning speed is not
within expected window
0x09 focus_timeout_error Focus could not be achieved
within the timeout
0x0A focus_retries_error The amount of focus retries ex-
pired
0x0B focus_agc_error The focus agc results are out of
range
0x0C radial_timeout_error Servo didn’t get on track within
the timeout
0x0D radial_retries_error Servo didn’t get on track after
several retries
0x0E radial_agc_error The radial agc results are out of
range
0x0F radial_init_error Unreliable signal scaling after the
radial initialisation
0x10 hf_pll_error HF-decoder pll could not lock to
HF signal
0x11 wobble_pll_error Wobble pll could not lock to wob-
ble signal
0x12 subcode_timeout_error Subcode information could not
be read
0x13 subcode_notfound_error Requested subcode item could
not be found
0x14 header_timeout_error Header information could not be
read
0x15 adip_timeout_error Adip information could not be
read
0x16 adip_window_error Adip address was not within ex-
pected window
0x17 adip_sync_error No adip sync was detected
0x18 atip_timeout_error Atip information could not be
read
0x19 atip_notfound_error Requested atip item could not be
found
0x1A atip_window_error Atip address was not within ex-
pected window
0x1B atip_sync_error No atip sync was detected
0x1C tray_error Tray could not be closed or
opened within the timeout
0x1D seek_error The requested seek couldn’t be
performed within the timeout
0x1E no_hf_present_error Attempt to read from a blank area
0x1F record_error An error occurred during the re-
cording
0x20 illegal_stopaddress_error The requested stopaddress with
modify-stop-address is not valid
0x21 no_disc_error No disc is detected
0x22 not_initialised_error The system is not initialised (e.g.
seek on unknown disctype)
0x23 illegal_medium_error BE detected an unsupported me-
dium during disc recognition
0x24 cd_frequency_error Measured HF frequency is not
within CD frequency range
0x25 dvd_frequency_error Measured HF frequency is not
within DVD frequency range
0x26 re-
served(non_existing_bca_
error)
Attempt to read non-existing bca
information
0x27 reserved(bca_read_error) An error occurred during reading
of bca information
0x28 selftest_error An error occurred during the self-
test of the BE
0x29 i2c_error The I2C interface does not oper-
ate
0x2A laser_pll_error Laser control pll did not lock or
lost lock on write clock
0x2B laser_forward_sense_erro
r
Forward sense value didn’t
change with changing laser pow-
er
0x2C jitter_optimisation_error An error occurred during optimis-
ation of the jitter
0x2D tilt_calibration_error An error occurred during calibra-
tion of the tilt frame
0x2E reserved
0x2F frontend_offset_calib_erro
r
The offset in the frontend couldn’t
be calibrated
0x30 reserved
0x31 wsg_calculation_error An error occurred in the calcula-
tion of the write strategy
0x32 buffer_overrun_error The buffer input stream overran
the buffer output stream
0x33 return_value_invalid_error The requested information is not
available for this inquiry
0x34 illegal_recording_speed_e
rror
The selected speed is not al-
lowed for a recording on this me-
dium
0x35 opc_media_parameter_err
or
The media parameters (info in
ATIP/ADIP) are invalid or not
read
0x36 opc_record_power_error The final optimum power was not
reached
0x37 opc_start_power_low_erro
r
OPC start power too low (opti-
mum power is higher)
0x38 opc_start_power_high_err
or
OPC start power too high (opti-
mum power is lower)
error
code
error meaning
To Next Page
Loading...
