15
English
Compact Disc
Playing a Disc
1
PressÉ to start playback.
➜ A flashing on the CD numeric flag indicates
the selected disc.
➜ The track number and elapsed playing time of
the current track appear on the display.
¶ To interrupt playback, pressÅ.
➜ The playing time flashes.
¶ To resume playback, pressÉ again.
2
To stop playback, press Ç.
Note:
– All the available discs will play once, then stop.
Disc Change
You can change the outer two discs while the
third inner disc is stopped or is playing.
1
Press DISC CHANGE.
➜ The CD changer tray slides out.
2
Replace the discs in the left and right disc trays.
¶ If you wish to change the inner disc during
playback, press DISC CHANGE again.
➜ "DISC CHANGE" will be displayed.
➜ The disc will stop playing.
➜ The CD changer tray will close to retrieve
the inner disc and then open again with the
inner disc accessible.
3
Press OPEN•CLOSE to close the CD changer
tray.
Selecting a desired track
Selecting a desired track when playback
is stopped
1
Press í or ë until the desired track appears
on the display.
2
PressÉ to start playback.
➜ The selected track number and elapsed
playing time appear on the display.
Selecting a desired track during playback
¶ Press í or ë until the desired track appears
on the display.
➜ The selected track number and elapsed
playing time appear on the display.
¶ If you press í once it will skip to the beginning
of the current track and play the track again.
Note:
–Pressing
í
during shuffling can only skip to the
beginning of the current track.
Searching for a particular
passage during playback
¶ Press and hold à or á until the desired
passage is located.
➜ The volume will be reduced.
¶ Play returns to normal when à or á is
released.
Programming Tracks
Programming tracks of a loaded disc is possible
when playback is stopped. The display will
indicate the total tracks stored in the
programme. Up to 40 tracks can be stored in
the memory in any order. When 40 tracks are
stored and you attempt to store another track,
the display will show “FULL”.
1
Load the desired discs in the disc trays.
2
Press PROGRAM to start programming.
➜ The PROG flag starts flashing.
➜ A flashing on the CD numeric flag indicates
the selected disc.
3
Press the CD (CD 1•2•3) or DISC 1/2/3
button to select the disc.
4
Pressí or ë to select the desired track.
5
Press PROGRAM to store the track.
¶ Repeat steps 3 to 5 to store other discs and
tracks.
6
Press Ç once to end programming.
➜ The total number of tracks programmed and
total playing time appear on the display.
Notes:
– If the total playing time is more than “
99
:
59
“
or if one of the programmed tracks has a number
greater than 30, then “
--
:
--
” appears on the
display instead of the total playing time.
– If the system is reading the discs, programming
is not possible, “
READING
” will be displayed and
followed by "
DISC X
". "
X
" is the current read disc
number.
– During programming, if no button is pressed
within 20 seconds, the system will exit programme
mode automatically.
–“SELECT A DISC” will be displayed when
programming an empty disc slot.
16
English
Reviewing the programme
Reviewing of the programme is possible only
when playback is stopped.
¶ Pressí or ë repeatedly to review the
programmed tracks.
¶ Press Ç to exit review mode.
Playing the programme
1
Press É to start programme playback.
➜ “PLAY PROGRAM” will be displayed.
➜ The track number and elapsed playing time of
the current track will appear on the display.
¶ If you press REPEAT during programme
playback, the current track or all programmed
tracks will be played repeatedly.
➜ “TRACK” or "PROGRAM" will be displayed.
➜ The REP and PROG flags appear on the
display.
2
Press Ç to stop programme playback.
Notes:
– If you press any of the DISC DIRECT PLAY
buttons, the system will play the selected disc and
the stored programme will be ignored temporarily.
The PROG display also will disappear temporarily
from the display. It will reappear when playback of
the selected disc ends.
– REPEAT DISC mode will be cancelled when
programme playback begins.
Erasing the programme
(when
playback is stopped)
¶ Press Ç.
➜ “PROGRAM CLEARED” will be displayed.
Note:
– The programme will be erased when the system
is disconnected from the power supply or when the
CD changer tray is opened.
Shuffle
(only on remote control)
In shuffle mode, the system plays all the available
discs and their tracks in random order. Shuffle
may be used also when tracks are programmed.
To shuffle all the discs and tracks
1
Press SHUFFLE.
➜ “SHUFFLE” will be displayed.
➜ The SHUF flag and the track selected at
random appear on the display.
¶ The discs and the tracks will be played in
random order until you pressÇ.
¶ If you press REPEAT during shuffling, the
current track or all available discs will be played
repeatedly.
➜ “TRACK” or “ALL DISC” will be displayed.
➜ The REP and SHUF flags appear on the
display.
2
Press SHUFFLE again to resume normal
playback.
➜ The SHUF flag disappears from the display.
Note:
– REPEAT DISC mode will be cancelled when
shuffle is selected.
Repeat
(only on remote control)
You can play the current track, a disc or all
available discs repeatedly.
1
Press REPEAT on the remote control to select
the various repeat modes.
➜ “TRACK”, “DISC”, “ALL DISC” or “OFF” will
be displayed.
➜ The REP flag appears on the display.
¶ The selected track, selected disc or all available
discs will now be played repeatedly until you
pressÇ.
2
Press REPEAT until the "OFF" mode is
displayed to resume normal playback.
➜ The REP flag disappears from the display.
Notes:
– REPEAT DISC mode is not available during
programme play or shuffle mode.
–You can also repeat shuffling a programme.
i) “TRACK“ or “PROGRAM" will be displayed.
ii)The REP, PROG, and SHUF flags appear on
the display.
Compact Disc
To Next Page
Loading...
