Philips FW-V795 - Radio Reception; Preset Station Storage

25
English
3139 115 21281
Radio Reception
FW-
VCD MINI HIFI SYSTEM
ECO POWER
CD 1•2•3
BAND
CDR/ DVD
TAPE 1•2
PROG
DUBBING REC
CLOCK•
TIMER
AUTO
REPLAY
STANDBY-ON
MUSIC LEVEL
INTERACTIVE VU METER
VOLUME
VOLUME
P
R
E
V
P
R
E
S
E
T
N
E
X
T
DEMO
STOP/
CLEAR
PLAY•
PAUSE
S
E
A
R
C
H
•
T
U
N
I
N
G
TUNER
TAPE AUX
DISPLAY
S
O
U
N
D
N
A
V
I
G
ATION - JOG
SOURCE
DOLBY
B NR
S
U
R
R
O
U
N
D
V
A
C
D
S
C
I
N
C
R
E
D
I
B
L
E
VCD
PAL/
NTSC
ON •OFF LEVEL
PB
C
R
E
T
U
R
N
TITLE/
ALBUM
NAME
T
I
T
L
E
A
L
B
U
M
MIC/
LEVEL
DYNAMIC AMPLIFICATION CONTROL
1
3
2
4
6
5
7
9
8
VOLUME
0
2
TAPE 1/2
OSD
VCD 123
AUX
TUNER
á
à
ë
í
Ç
É
Å
TITLE
_
TITLE
+
ALBUM
_
ALBUM
+
MP3 123
REPEATPROG
MP3
-
CD
ECO POWER
Storing Preset Radio Stations
You can store up to 40 preset radio stations in
the memory.
Automatic Preset Programming
● Plug and Play setting (refer to “Basic Functions -
Plug and Play”).
OR
1 Press TUNER (BAND) to select TUNER mode.
➜ "TUNER" will be displayed. A few seconds
later, the current radio frequency will appear on
the display.
➜ If an FM station is received in stereo, will
appear on the display.
To begin automatic preset from a desired
preset number
● Press í or ë to select the desired preset
number.
➜ If a radio station has been stored in one of
the presets, it will not be stored again under
another preset number.
2 Press and hold PROG until "AUTO" appears on
the display.
➜ PROG will start flashing.
➜ The system will start searching for all radio
stations on the FM band, then the MW band.
➜ All available radio stations with strong signal
strength will be stored automatically.
➜ The system will stop searching when all the
available radio stations are stored or when the
memory for 40 preset radio stations is used.
➜ The last preset radio station will then be
played when completed.
To stop storing the automatic preset
● Press PROG or Ç on the system.
Note:
– If no preset number is selected, automatic preset
will begin from preset (1) and all your former
presets will be overridden.
Manual Preset Programming
1 Press TUNER (BAND) repeatedly to select the
desired waveband : FM or MW.
2 Press PROG.
➜ PROG will start flashing.
➜ The next available preset number will be
displayed for selection.
3 Press and hold à or á until the frequency
indication starts to change, then release.
➜ The display will show "SEARCH" until a radio
station with sufficient signal strength is found.
To store the radio station to another
preset number
● Press í or ë to select the desired preset
number.
4 Press PROG again to store the radio station.
➜ PROG will disappear from the display.
● Repeat steps 2–4 to store other preset radio
stations.
pg 001-035/V795/21-Eng 4/16/02, 6:44 PM25