Phocos Any-Grid PSW-H-5kW-230/48V User Manual (English)

Other manuals for Phocos Any-Grid PSW-H-5kW-230/48V

Questions and Answers:

James WilliamsAug 26, 2025

What to do if Phocos Any-Grid PSW-H-5kW-230/48V Battery Charger has no response after power on?

M
Maria SantiagoAug 26, 2025
If your Phocos Battery Charger doesn't respond after you power it on, the battery voltage may be too low (less than 33.6V/16.8V for the 48V/24V model) or the battery polarity is connected in reverse. First, check if the batteries and wiring are correctly connected, paying attention to the battery polarity. Then, try recharging the battery. If the issue continues, consider replacing the battery.

thompsonpatriciaAug 25, 2025

How to fix Phocos Any-Grid PSW-H-5kW-230/48V Battery Charger when the unit shuts down automatically during start-up process?

K
Kara EdwardsAug 26, 2025
If your Phocos Battery Charger shuts down automatically during the start-up process, it's likely because the battery voltage is too low (less than 45.84V/22.92V for the 48V/24V model). To resolve this, first try to re-charge the battery. If the issue persists, you may need to replace the battery.

Output Power	5000 W
DC Input Voltage	48 V
AC Output Voltage	230 V
Battery Voltage Range	40-60V
MPPT Chargers	1
Max PV Input Power	6000 W
Max PV Input Voltage	500V
Model	Any-Grid PSW-H-5kW-230/48V
Rated Power	5000 W
Communication	RS485, CAN
Type	Hybrid Inverter
Protection	Overload, Short Circuit, Over Temperature

Output Power

5000 W

DC Input Voltage

48 V

AC Output Voltage

230 V

Battery Voltage Range

40-60V

MPPT Chargers

Max PV Input Power

6000 W

Max PV Input Voltage

500V

Model

Any-Grid PSW-H-5kW-230/48V

Rated Power

5000 W

Communication

RS485, CAN

Type

Hybrid Inverter

Protection

Overload, Short Circuit, Over Temperature

Summary

Installation

Mounting the Unit

Provides instructions and safety warnings for securely mounting the Any-Grid unit on a wall.

Battery Connection

Guides on connecting the battery, including cable sizing, fuse rating, and polarity warnings.

AC Input and AC Output Connection

Instructions for connecting AC source and loads, including breaker requirements and wiring precautions.

PV Connection

Details how to connect PV modules, including cable sizing, breaker ratings, and voltage/current specifications.

Installing Multiple Units: Parallel, Split Phase, or 3-Phase Configuration

Explains how to install multiple Any-Grid units in parallel, split-phase, or 3-phase configurations.

Commissioning Multi-Unit Systems

Single-Phase Parallel Commissioning

Step-by-step guide for commissioning multiple units in a single-phase parallel configuration.

3-Phase System Commissioning

Guide for commissioning units in a 3-phase configuration, detailing settings for each phase.

Split-Phase (2-Phase) System Commissioning

Instructions for commissioning units in a 2-phase split-phase configuration.

Operation

Inverter Power ON/OFF

Details the procedure for turning the inverter's AC output on and off using the ON/OFF switch.

Device Operation Settings Navigation

Introduces how to access and navigate the unit's settings menus for configuration.

AC Output Source Priority Configuration

Configures the priority of power sources (Utility, Solar, Battery) for supplying AC output loads.

Maximum Total Battery Charging Current Setting

Sets the combined maximum charging current from AC and solar sources for battery health.

Battery Type Configuration

Selects the battery type (UPS, AGM, Pylontech, etc.) to optimize charging and protection.

Solar Power Feed-in to Grid Setting

Configures grid feed-in functionality, requiring a PIN code for activation and legal checks.

Maximum AC Source Charging Current Setting

Limits the maximum charging current from the AC source to protect certain battery types.

Grid/Off-Grid Switchover Voltage (SBU Priority)

Sets the battery voltage threshold for switching between Grid and Off-Grid modes in SBU priority.

Battery Charger Source Priority Configuration

Configures which power sources (Solar, Utility) are prioritized for charging the battery.

Boost Battery Charging Voltage Setting

Sets the voltage level for the boost charging phase of the battery.

Floating Battery Charging Voltage Setting

Sets the voltage level for the floating charging phase of the battery.

Battery Equalization Voltage Setting

Sets the voltage for battery equalization to prevent sulfation and balance cells.

Battery Equalization Duration Setting

Sets the duration for which the equalization voltage is held before the floating phase.

Battery Equalization Timeout Setting

Sets the timeout for equalization if the target voltage is not reached.

Maximum Discharging Current Setting

Timer Override for AC Output Source Priority

Timer Override for Battery Charger Source Priority

Operating Mode Description

Troubleshooting Common Issues

Unit Shuts Down During Start-up

Addresses issues where the unit automatically shuts down during the initial startup process.

No Response After Power On

Troubleshoots scenarios where the unit does not respond or show any indication after being powered on.

AC Source Present, Unit Operates in Off-Grid Mode

Diagnoses why the unit operates in Off-Grid mode when an AC source is available.

Internal Relay Repeatedly Switches On/Off

Solves the issue of the internal relay repeatedly switching on and off after the unit is turned on.

Buzzer Beeps Continuously With Red LED

Addresses troubleshooting when the buzzer beeps continuously and the red LED is on, indicating faults.

Phocos Any-Grid PSW-H-5kW-230/48V User Manual

Table of Contents