Phottix Mitros - Group and Ratio Adjustments; ETTL Group and Ratio Settings; Manual and Multi Group Settings

10
ETTL Modes
A+B+C All three groups re at an average of the total calculated output.
A:BC Groups A and B can be set by Flash Ratio (see below). Group C is inde-
pendent with its ash output level assigned by the camera.
The EV compensation of Groups A and B can be adjusted.
1. Press the button after exiting the Flash Ratio Setting Screen.
2. Press the or buttons to adjust up or down EV for Groups
A and B.
3. The EV compensation for Group C can also be adjusted.
4. Pressing the button after setting the ash ratio will move the high-
lighted selection to EV adjustment for Group C.
5. Press the or buttons to adjust the EV for Group C.
A:B Groups A and B can be set by Flash Ratio (see below). Group C is not
adjustable and does not re.
The EV compensation of Groups A and B can be adjusted.
1. Press the button after exiting the Flash Ratio Setting Screen.
2. Press the or buttons to adjust up or down EV for Groups
A and B.
Setting and Adjusting Ratio Modes
ETTL Modes
1. Press and hold the button for 2 seconds to enter wireless mode.
2. Pressing the and buttons will cycle between Master with
ash, Master without ash, Slave, OS and O modes.
3. Select Master with ash or Master without ash.
4. Pressing button will change the highlighted selection from Master
to Channel and Ratio.
5. Select the transmission channel.
6. Select the Ratio mode. Pressing the and buttons will cycle
between A+B+C, A:B and A:BC modes.
7. When A:B or A:BC are highlighted pressing the button will highlight
the ratio adjustment selection below the ratio.
8. Pressing the button will change the ratio from 1:1 to 1:8 in steps of
1:1.5, 1:2, 1:3, 1:4, 1:6, 1:8.
9. Pressing the button will change the ratio from 1:1 to 1.5:1, 2:1, 3:1,
4:1, 6:1, 8:1.
10. Press the button to conrm and exit the screen.
Manual Modes
A+B+C In manual mode all three groups re at the same output level. This
power level can be set.
A:B:C The output level of each group is individually adjusted by the user (see
below). Each group is independent, one not aecting the other.
A:B Groups A and B power level can be set individually by the user (see be-
low). Group C is not adjustable and does not re.
Setting and Adjusting Manual Modes
1. Press the button to change the ash into Manual (M) Mode.
2. Press and hold the button for 2 seconds to enter wireless mode.
3. Pressing the and buttons will cycle between Master with
ash, Master without ash, Slave, OS and O modes.
4. Select Master with ash or Master without ash.
5. Pressing button will change the highlighted selection from Master
to Channel and Ratio.
6. Select the transmission channel.
7. Select the Ratio mode. Pressing the and buttons will cycle
between A+B+C, A:B and A:B:C modes.
8. Press the button to conrm and exit the screen.
9. Press the button to adjust power levels.
10. Pressing the or buttons will change the Flash Power Level
(1/1 to 1/128 in 1/3rd stops).
11. Pressing the button will change the Groups from A to B to C,
the button from C to B to A (if applicable).
12. Press the button to exit power level adjustment mode.
Multi Mode
A+B+C All three groups re in Multi Mode at the same power level, frequen-
cy and ash count.
A:B:C The output level of each group is adjusted individually by the user (see
below). The frequency and ash count of the multi strobe of each group are
same and can only be adjusted on Group A.
A:B Groups A and B can be set by power level individually by the user (see
below). The frequency and ash count of the multi strobe of Groups A and
B are same and can only be adjusted on Group A. Group C is not adjustable
and does not re.
Setting and Adjusting Multi Mode
1. Press the button to change the ash into Multi Mode.
2. Press and hold the button for 2 seconds to enter wireless mode.
3. Pressing the and buttons will cycle between Master with
ash, Master without ash, Slave, OS and O modes.
4. Select Master with ash or Master without ash.
5. Pressing button will change the highlighted selection from Master
to Channel and Ratio.
6. Select the transmission channel.
7. Select the Ratio mode. Pressing the and buttons will cycle
between A+B+C, A:B and A:B:C modes.
8. Press the button to conrm and exit the screen.
9. Press the button to adjust power levels.
10. Pressing the or buttons will change the Flash Power Level
(1/1 to 1/128 in 1/3rd stops).
11. Pressing the buttons will change the Groups from A to B to C,
the button from C to B to A (if applicable), and allow power level to
be changed on these groups.
12. Pressing the button after cycling through the groups will move to
the frequency and ash count selections.
13. Pressing the or buttons will allow changes to be made to
frequency and ash count. These setting can only be changed on Group A
and will be applied to Group B or C (if applicable).
14. Press the button to exit power level adjustment mode.
En
INSTRUCTION MANUAL