Pioneer AVIC-X910BT - User Manual

AVIC X-Series Firmware Update Instructions
INSTRUCTIONS FOR DOWNLOADING FIRMWARE UPDATE
FOR AVIC-X910BT, AVIC-X710BT, AVIC-X9115BT and AVIC-
X7115BT
**After you download the firmware update files onto your computer, you will need to
transfer the files to an SD card (512MB or larger) in order to install them on your
navigation system.
Important
Please print or save these Instructions before downloading and installing the firmware update
-- it is very important that you complete all steps correctly and in the order described below.
Failure to do so could cause data stored onto your navigation system to be permanently lost.
WARNING!
This firmware update applies only to models sold in the U.S.
If you have any difficulty carrying out these instructions, please contact the Pioneer Customer
Service Center at 1-800-421-1404. Pioneer service representatives are available Monday
through Friday, 10:00 a.m. to 7:30 p.m. (Eastern Time).
Before Downloading the Firmware Update
Please check your system version number by doing the following to determine whether your
system has already been updated with the new firmware update:
1. Press the "Menu" button
2. Touch the "Settings" tab;
3. Touch the “System Settings” tab;
4. Touch the “Service Information” tab;
5. The "Map version" number and the "Version" number are both displayed -- please look at the
"Version" number, which is displayed on the lower line; and
6. If the "Version" number is "3.010100" or an earlier/smaller number, please install the new
firmware update. If the "Version" number is "3.020100" or a later/larger number, the system
has already been updated with the new firmware.
Downloading the Firmware Update & Transfer to an SD Card
Step 1
1-1. Download the system firmware update Zipfile onto your computer by clicking here
. The
location where you save the downloaded Zipfile should be accessible and easily remembered.
1-2. After you have downloaded the Zipfile, locate it on your computer and double click to
decompress it.*
Once the Zipfile is decompressed, locate and open the folder named "X-Series Firmware
Update".
Once the folder "X-Series Firmware Update" has been opened, locate within it the sub-
folders named "LPUE080".
*If you do not have a decompression utility on your computer, you can download WinZip
at http://www.winzip.com
.
1-3. Transfer the "LPUE080" folder onto the top layer (folder) of your SD card. **
**You must use a SD card that is 512MB or larger and formatted with a FAT16 or FAT32
file system.

Summary

Before Downloading the Firmware Update

Check System Version

Steps to verify the current system version number before proceeding with the firmware update.

Download and Transfer Firmware

Download and Decompress Firmware Files

Instructions for downloading the firmware ZIP file and decompressing it on your computer.

Transfer Files to SD Card

Guide on copying the decompressed firmware folder to the SD card.

Install Firmware Update on Navigation System

Prepare for Installation

Disconnect devices and insert the SD card into the system before turning it on.

Initiate and Monitor Update

Turn on the vehicle and navigation system to start the automatic update process.

Post-Update Reboot Procedures

Actions to take after the system reboots, including troubleshooting boot issues.

Confirm and Finalize Update

Verify Successful Installation

Steps to check the system firmware version to confirm the update was successful.

Perform Post-Update Calibration

Guide for calibrating the system's touchscreen after the firmware update.

Pioneer AVIC-X910BT Specifications

General

Display Size	6.1 inches
Resolution	800 x 480 pixels
Touchscreen	Yes
Navigation	Yes
Bluetooth	Yes
USB Port	Yes
iPod Compatibility	Yes
DVD Player	Yes
CD Playback	Yes
Radio Tuner	Yes
Preamp Outputs	3 pairs
Max Power Output	50 watts
Video Output	Yes
Rear Camera Input	Yes
Steering Wheel Control	Yes
SD Card Slot	Yes
Audio Formats Supported	MP3, WMA, AAC
Audio Output	4 channels
Video Formats Supported	AVI, MPEG