Pioneer PD-F904 - Programmed Playback Functions; Programming Tracks and Discs; Disc All and Direct Program Modes

1
5 5
2,3 1
3 2
2 3
PD-F904 PD-F100E
1
PGM
] f= FGM
u <
— J) PD-F904 Ye PD-F100E |
2
bey pty ot r— Ser
Cacac3
cp
CD
CD
DISC
oct ee ce
moo OoOee » PD-F904
co [oon DE.
SET
PD-Fa04. =“) PD-F100E
/) Pe. PD-F100E
3 |
. ; ; SET—
SF Ooo wt we oo TRACK
mobo @e » PD-F904
oS for) TRACK
PD-F904 PD-F100E
4) i) PD-F100E
——
5
Disc all program |
This operation can only be performed in stop mode.
if only disc No. is entered, and “AL” appears on the display, all
tracks on the disc can be programmed.
e Disc ail program mode is cancelled when the track number is
entered.
@ Disc all programming cannot be carried out during playback.
Direct program
@ Press the PGM button during normal playback.
During normal playback, the track being played can be programmed.
1. Press PGM to enter the program mode.
2 If you wish to program the track currently playing, press PGM
while the track is playing.
@ Direct programming is not possible during program playback.
16
<PRE1222>
En
Program playback - To program tracks/discs
i in desired order
You can perform this operation in either stop or playback mode.
However, Ke and &Pmt cannot be used to select tracks during
playback. Be sure toselect stop or playback mode bofore programming
e@ Pressing » when the program indicator is lit starts program
playback in the programmed order,
1 Press PGM on the remote control unit.
e@ The PGM indicator lights.
2 Select the disc number which contains the track
to be programmed with the digit buttons, and
then press the DISC SET button.
To program entire discs, enter the desired disc numbers with
the digit buttons and DISC SET, and then go to step 4. Make
sure that the player is in stop mode for Disc programming.
@ When the DISC SET button is pressed, "AL" {all tracks) appears
on the display.
@ When the disc number is programmed, the PGM indicator, the
disc No. and the track No. blink,
@ Only in stop mode can you use the DISC -/+ buttons. After
selecting the disc No., press DISC SET.
3 Enter the track No. to be programmed with the
digit buttons and then press the TRACK SET
button.
Only in stop mode can you use I< or mm, After selecting the
track No., press TRACK SET.
e@ When the track number is programmed, the PGM indicator, the
disc No. and the track No. blink.
4 Repeat steps 2 and 3 to program other tracks.
5 Press >.
The tracks are piayed in the programmed order.
NOTE:
When the disc number is selected with DISC -/+ in step 2, and when
the track is selected with <4 or »®i in step 3 in stop mode, the
displayed disc No. or track No. is automatically programmed if <4 or
bP is not pressed within 2 seconds. Therefore, be sure to press DISC
-/+ Of Kt, Bt sequentially until the desired disc No. or track No,
appears on the display.
To stop Program playback, press m.
@ Programs containing up to 32 steps can be created.
@ The program contents will not be erased even if the power is
turned off.
@ When DISC ~/+ is pressed in the program playback mode, the
program mode is cancelled, and the program contents are
cleared. The player searches for the disc in ALL mode.
@ When the programmed dise cannot be detected in program
playback mode, or the programmed track cannot be detected
after TOC is read, that programmed step is cancelied.
“*** no" is displayed for about 3 seconds, and next step is
Played back.