Pioneer VSA-700 User Manual

Operating
Instructions
MD PIONEER wncin wrmne amos ne ue
AV DIGITAL SURROUND AMPLIFIER
AMPLIFICATORE DIGITALE
AV DI CIRCONDAMENTO
VSA-70
Thank you for buying this Pioneer product. Please read through these operating instructions
so you will know how to operate your model properly. After you have finished reading the
instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes
differ from that shown in the explanatory drawings. However, the method of connecting and
operating the unit is the same.
WARNING: to prevENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the
rear panel. Please write this serial number on your
enclosed warranty card and keep it in a secure area. This
is for your security.
[For Canadian model]
CAUTION: To prEvENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
ATTENTION: pour prevenin LES cHocs
ELECTRIQUES NE PAS UTILISER CETTE FICHE
POLARISSE AVEC UN PROLONGATEUR UNE PRISE DE
COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF
SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS
EN LAISSER AUCUNE PARTIE A DECOUVERT.
LINE VOLTAGE SELECTOR SWITCHES
Only multi voltage models are provided with these
switches, U.S.A., Canadian, U.K., Australia and Europe
models are not provided with them.
Mains voltages in Saudi Arabia are 127V and 220V only.
Never use this model set to 110V in Saudi Arabia.
You will find the line voltage selector switches on the rear panel.
Before
your
model
is
shipped
from
the
factory,
the
switches
are set to the power requirements of the destination;
nevertheless, you should check that they are set properly before
plugging the power cord into the wall outlet. If the voltage
requirements differ, adjust the selector switches as follows.
Before adjusting, disconnect the power cord.
1. Provide yourself with a medium size screwdriver.
2. Changing the position of switch A, B
Insert the screwdriver into the slot on the voltage selector and
adjust so that the tip of the slot points to the voltage value of
your area.
Changing the position of switch A, B
Set it to the power voltage of your area.
NOTE:
Both switches A and B must be set to the same voltage.
oO an Switch A
Switch B
ie o
nov iS iar |
WY) PIONEER’
The future of sound and vision.

Pioneer VSA-700 Specifications

General

Channels	2
Input sensitivity (MC)	0.2mV
Input sensitivity (MM)	2.5mV
Input sensitivity (line)	150mV
Frequency Response	5Hz-100kHz (+0dB, -3dB)
Input Sensitivity	150mV (line)
Speaker load impedance	4Ω to 16Ω

Summary

Important Notice and Safety Warnings

General Safety Warnings

Essential warnings to prevent fire, shock, and damage to the appliance.

Canadian Model Shock Prevention

Specific caution for Canadian models regarding polarized plugs and blade exposure.

Line Voltage Selector Switch Adjustment

Comprehensive Safety Instructions

Outdoor Antenna Grounding Guidelines

Procedures for grounding outdoor antennas to prevent voltage surges and static charges.

User Information for US Models

Product Features Overview

Before Unit Operation Preparations

Preparations and accessories needed before operating the unit, including remote control.

Understanding Surround Sound Effects

Stadium Surround Mode Explained

Describes the Stadium surround effect for sports broadcasts and similar audio.

Simulated Surround Mode Explained

Details the Simulated Surround mode for monaural sources to enhance presence.

Dolby Surround Mode Explained

Covers the Dolby Surround mode for movies and music playback.

Front Panel Facilities Guide

Power, Speaker, and Basic Input Controls

Controls for powering the unit, speaker selection, remote sensor, and basic input/output selectors.

Audio and Video Input Selection Switches

Switches for selecting audio and video input sources like DAT, CD, VCR, and TV.

Surround, Volume, and Tone Adjustments

Controls for surround modes, master volume, muting, treble, and bass adjustments.

Display, Memory, and Special Function Switches

Includes display functions, acoustic memory, video adaptor, and noise filter switches.

Delay Time and Balance Adjustments

Switches for surround delay time, simulated stereo, and balance controls.

Rear Panel Facilities Guide

Control, Audio, and Pre-Amp Terminals

Terminals for control signals, CD, DAT/TAPE, VDP/CDV, and pre-amp outputs.

Advanced Audio/Video and Power Terminals

Terminals for surround power amp input, balance control, and front pre-amp output.

Input/Output, Speaker, and Power Terminals

Terminals for VCR, TV, Video Adaptor, Phono, Tuner, AC outlets, and speaker impedance.

Speaker and Surround Switch Settings

Details on speaker terminals, impedance switch, and surround switch configuration.

System Connection Diagrams

Audio Connection Setup Guide

Instructions for connecting audio sources like CD, Tape, DAT, and Turntable.

Video Connection Setup Guide

Instructions for connecting video sources like VCR, TV, and VDP.

Power Cord and Speaker Wiring

Details on power cord connections and speaker wiring configurations.

Input/Output and Remote Cord Connections

Guidelines for connecting input/output and remote control cords.

Remote Control Operations

Remote Control Basics and Modes

Covers battery loading, range, replacement, and function modes for the remote unit.

Remote Control Function Modes

Explains how to select modes for controlling different devices using the remote.

Device Operation with Remote Control

Detailed operations for Tape Deck, VCR, CD Player, and Amplifier using the remote.

Specific Device Operations via Remote

Covers CD player, VDP, Tuner, Turntable, and TV operations via the remote.

Amplifier and Surround Control via Remote

Focuses on amplifier functions, surround modes, and volume controls via the remote.

Advanced Remote Control Learning Functions

Presetting Remote Control Keys

How to program keys for specific device functions using the learning feature.

Learning Function Operation Example

Step-by-step example of learning a VCR playback command.

Learning Function Q&A and Initial Settings

Addresses common learning function questions and how to reset settings.

Performing Audio and Video Operations

Audio Source Playback and Adjustment

How to play back audio sources and adjust settings like volume and tone.

Video Source Playback and Recording

How to play back and record video sources, including VCR and VDP.

Tape Dubbing Procedures

Step-by-step guide for dubbing audio and video tapes between decks.

System Block Diagram

Troubleshooting Common Issues

Technical Specifications