Why can’t I record video using my Pioneer VSX-AX3-S?
The source may be copy protected, and you can’t record sources that have been copy protected. The recorder’s video input may be hooked up using a different type of cord to the source video output. Hook up the source and the recorder using the same type of video cord.
What to do if there is no sound output when a function is selected on my Pioneer VSX-AX3-S?
Check the following: * Ensure all components/speakers are connected correctly. * Press MUTING on the remote control to unmute. * Adjust MASTER VOLUME to increase the volume. * Press SPEAKERS (A/B) to select the connected speakers. * Select the proper signal with the SIGNAL SELECT button. * Turn MULTI CH IN mode off.
How to fix considerable noise in radio broadcasts on Pioneer Receiver?
First, tune in the correct frequency. Then, ensure the antenna is properly connected. Also, route digital cables away from the antenna terminals and wires, as they may cause interference.
What to do if my Pioneer Receiver is not responding when the buttons are pressed?
Static electricity caused by dry air may be the reason. Try switching the unit off, then on again. If that doesn't work, disconnect the power plug from the outlet, and then plug it back in.
Why is there no image output when a function is selected on my Pioneer VSX-AX3-S Receiver?
Check that the component is connected correctly and that you have selected the correct function button. Also, ensure the video input selected on the TV monitor is correct, consulting your TV monitor manual if needed. Verify that the same type of cable is used to connect the TV and all your video equipment.
What causes noise or hum to be heard even when there is no sound being input on my Pioneer Receiver?
There may be electrical interference from another component or appliance. Check that personal computers or other digital components connected to the same power source are not causing interference.
Why does a multi channel DVD source appear to be downmixed from 2 channels during playback on my Pioneer VSX-AX3-S?
The source may be coming from something other than the MULTI CH IN jacks. Check the MULTI CH IN connection and select the type of playback with the MULTI CH IN button.
Why can't broadcast stations be selected automatically on my Pioneer VSX-AX3-S?
The antenna may be poorly positioned, so adjust the direction and position for best reception. There may be interference caused by other equipment (fluorescent lamp, motor, etc.), so turn off the equipment causing the noise or move it away from the receiver. The radio signals may be weak, so connect an outdoor AM or FM antenna.
What does THDCT NG blinking in the display of my Pioneer Receiver mean?
The thermistor (temperature sensor) is broken. Turn the receiver off, unplug it from the wall, and call a Pioneer-accredited repair center to look at the problem.
What does FAN STOP blinking in the display of my Pioneer VSX-AX3-S mean?
Something may be stuck in the fan, or the fan is broken. Remove any foreign object from the fan. If you can’t do this, or the fan is broken, call a Pioneer-accredited repair center to look at the problem.
Provides guidelines for proper installation to ensure adequate heat radiation and prevent overheating.
Warns against blocking ventilation slots to prevent fire hazard and ensure reliable operation.
Specifies optimal temperature and humidity conditions and locations to avoid for operation.
Advises on setting voltage selectors correctly for specific regions and warns about incorrect settings.
Describes the MCACC system for automatic surround sound setup and parameter adjustment.
Highlights support for advanced audio formats and high-definition video compatibility.
Lists all accessories included with the product to ensure completeness upon purchase.
Provides instructions for loading batteries into the remote control for operation.
Introduces fundamental concepts of home theater sound systems and factors contributing to surround sound.
Explains how to connect a DVD player and TV using digital and analog audio/video connections.
Provides instructions for connecting speakers, including front, center, surround, and surround back channels.
Guides through the automatic MCACC system setup for optimal surround sound configuration.
Explains how to connect the TV using S-video or composite video cords for signal transmission.
Provides specific instructions for connecting a DVD player, including digital and analog audio connections.
Guides connecting players with multichannel analog outputs for high-resolution audio formats.
Details connecting various speaker configurations, including surround back speakers and impedance recommendations.
Explains the functions of all controls and indicators on the receiver's front panel.
Details the buttons on the remote control and their functions for operating the receiver.
Explains the meaning of various indicators and symbols shown on the receiver's display.
Describes all terminals and connectors located on the rear panel of the receiver.
Provides access to surround sound configuration options, including Auto, Normal, and Expert settings.
Offers manual adjustment of sound parameters for surround sound, overriding auto settings.
Explains how to balance speaker sound output levels using manual or automatic test tones.
Guides on setting speaker distances to adjust delay times for improved sound depth and separation.
Instructions on how to play sound sources and adjust volume for stereo and multichannel audio.
Explains how to select input signals (AUTO, ANALOG, DIGITAL) for proper source playback.
Describes various listening modes (MOVIE, MUSIC, STEREO, DIRECT) for different audio sources and preferences.
Details various MOVIE listening modes, including pure decoding and DSP modes for enhanced movie soundtracks.
Explains how to use the ACOUSTIC CAL EQ feature for sound calibration and equalization.
Provides steps for tuning FM and AM radio broadcasts using automatic or manual methods.
Instructions on memorizing up to 30 radio stations in 3 classes for quick recall.
Introduces the Radio Data System (RDS) and its features like Program Service Name and Program Type search.
Guides on programming the remote control to operate other audio/video components using preset codes.
Describes the learning mode for programming new commands from other remote controls.
Explains how to set the direct function for external video sources to allow remote control without changing the receiver mode.
Guides on making recordings from one component to another, covering analog and digital connections.
Explains setting up a second zone of stereo speakers using surround back terminals.
Guides on programming multi-button operations to control multiple components sequentially.
Explains how to program a single button to turn off the receiver and other connected components.
Allows selection of decoding methods for THX CINEMA mode, enhancing 2-channel source playback.
Guides on assigning digital inputs to specific components for proper remote button correspondence.
Provides advanced settings for fine-tuning surround sound, building upon basic setups.
Determines frequency division between subwoofer and speakers for optimal bass management.
Allows precise balancing of sound output levels for each speaker.
Guides on adjusting speaker delay times for improved sound depth and separation.
Explains using Auto Surround Sound Setup or manual EQ adjustments for room acoustics.
Guides on limiting peak levels for the LFE channel to prevent distortion from ultra-low bass tones.
Explains Dolby Digital surround sound format, its features, and dialog normalization.
Details DTS Extended Surround format for enhanced 6.1 channel surround sound with surround back channels.
Introduces THX technology for accurate cinema sound presentation, including features like Re-Equalization.
Addresses power-related issues like unit not turning on or switching off during loud playback.
Provides solutions for when the setup screen is not displayed, checking connections and settings.
Addresses issues with low subwoofer output, checking settings and connections.
Guides on troubleshooting lack of video output by checking connections and input selections.
Lists common causes and remedies for the remote control not functioning, such as battery issues or obstacles.
Lists manufacturers and their corresponding remote control preset codes for DVD players.
Details the continuous power output specifications for different speaker channels.
Lists the maximum output power specifications for the multi-voltage model.
To Next Page
General