PixelRange PixelPar - Control Menu Contents

3


















































 





SetsthebaseDMXaddressfromwhichthecontrolchannelswillbegin.
Showsthemainprocessorsoftwarerevision.Nochangesarepossiblewithin
this option. Press whileviewingthisoptiontoseethesoftwaresub-revision.
Showsthedisplaycontrollersoftwarerevision.Nochangesarepossiblewithin
this option.
Selectstheprimaryinternalchaseeffect.SeeChaseeffectsfordescriptions.
Select MODE > EF Mtoshowtheselectedchase.
Selectsthecrossfadespeedbetweenthestepsoftheselected
C1chaseeffect.
SelectsthespeedoftheselectedC1chaseeffect.
SelectsthemasterintensitylevelofchaseeffectsC1 and C2.
Selectsthesecondaryinternalchaseeffect.SeeChaseeffectsfordescriptions.
Select MODE > EF Mtoshowtheselectedchase.
SelectsthecrossfadespeedbetweenthestepsoftheselectedC2chaseeffect.
SelectsthespeedoftheselectedC2chaseeffect.
Sets the red intensity. Select MODE > MANU(manual)toshowtheresult.
Sets the green intensity. Select MODE > MANU(manual)toshowtheresult.
Setstheblueintensity.SelectMODE > MANU(manual)toshowtheresult.
Setstheamberintensity.SelectMODE > MANU(manual)toshowtheresult.
OnRGBWmodels,thisentrywillshowWHIT.
Selectsnumberofchannelsrequiredtocontrolallemitters.Optionsare1,3and4.
Emitters are grouped together accordingly.
Determineswhetherthisxturewillactasamastercontrollingothers.
WhencontrolledviaDMXthisxturemustbesettoSLAV.
DMX and 16btmodesonly.WhensetONthisenablesthemasterintensitychannel.
WhensetoN,thisoptionscrollsthroughtheprimarycoloursatpoweronto
demonstratecorrectoperationoftheemitters.
Determinestheintensityofthefourdigitcontrolpaneldisplay.Valuesrangefrom
0(dimmest)to15(brightest).
WhensettoAOFF,thecontrolpaneldisplaywillblankout60seconds
afterthemenuisexited.Thedatadotindicatorwillremainactive.
Providesaselectionofdimmercurves(FINE,TV,TUNG or LGCY)tosuitparticular
circumstances.Seenextpagefordescriptionsofeachoption.
RGBA
§
controlusinganexternalDMXcontrolinput.PERS > MINT set to ONprovides
a master intensity in DMX and 16btmodes.Nochaseeffectsareselectable.
DisplaystheresultingRGBA
§
levelsthataresetviatheMANsectionoftheinternal
menu.ExternalDMXcontrolisnotpossibleinthismode.
Ch1to3:C1Effect,Speed&Xfade,Ch4to6:C2Effect,Speed&Xfade,
Ch7:Masterintensity.
Displaysthechaseeffect(s)determinedwithinthePROGsection.ExternalDMX
controlisnotpossibleinthismode.
DMXCh1to4:RGBA
§
colourmixing,Ch5to7:C1Effect,Speed&Xfade,
Ch8to10:C2Effect,Speed&Xfade,Ch11:Masterintensity.
16bitRGBA
§
controlusing2xthenumberofDMXchannelsdeterminedbyPERS>RES.
PERS>MINT set to Onprovidesamasterintensity.Nochaseeffectsareselectable.
Control menu contents