What to do if my pleasant hearth Wood stove has a gas odor during combustion?
If you notice a gas odor during combustion with your pleasant hearth Wood stove, it could be due to foreign matter between the control valve and burner. Try taking apart the gas tubing and removing any foreign matter. It could also indicate a gas leak, in which case you should locate and correct all leaks.
What to do if my pleasant hearth VFS-PH30DT heater shuts off in use?
If your pleasant hearth Wood stove heater shuts off while in use, it might not be getting enough fresh air. Try opening a window or door for ventilation. It could also be due to low line pressure, in which case you should contact your local gas supplier. Another possibility is that the ODS/pilot is partially clogged; consider cleaning it.
Why is there no spark at ODS/ pilot when I press the ignitor button on my pleasant hearth Wood stove?
If there's no spark at the ODS/pilot when you press the ignitor button on your pleasant hearth Wood stove, several things could be wrong. The ignitor electrode might be positioned incorrectly or broken, in which case you should replace the electrode. The ignitor electrode might not be connected to the ignitor cable, or the cable could be pinched, wet, or damaged; consider replacing the ignitor cable, freeing it from any obstructions, and keeping it dry. Also, the piezo ignitor could be bad, requiring replacement. Finally, check the battery and replace it if needed.
What to do if my pleasant hearth VFS-PH30DT Wood stove heater produces unwanted odors?
If your pleasant hearth Wood stove heater is producing unwanted odors, it could be burning vapors from paint, hair spray, or glues. Ventilate the room and stop using odor-causing products while the heater is running. Another cause could be a gas leak, so locate and correct any leaks. Low fuel supply can also cause this issue, so refill the supply tank if you have a propane/LP model.
Why does the ODS/pilot light but the flame goes out when I release the control knob on my pleasant hearth Wood stove?
If the ODS/pilot lights but the flame goes out when you release the control knob on your pleasant hearth Wood stove, make sure the control knob is fully pressed in and held for at least 30 seconds after the ODS/pilot lights. Also, ensure the equipment shutoff valve is fully open. The thermocouple connection may be loose, so hand tighten it until snug, then tighten an additional ¼ turn. If the issue persists, the thermocouple may be damaged and need replacing.
What to do if my pleasant hearth Wood stove has a high yellow flame during burner combustion?
If your pleasant hearth Wood stove displays a high yellow flame during burner combustion, it could be due to not enough air. Check the burner for dirt and debris. If the burner is dirty, clean it. The gas regulator could also be defective and require replacement.
What to do if my pleasant hearth VFS-PH30DT Wood stove burner backfires during combustion?
If the burner is backfiring during combustion in your pleasant hearth Wood stove, it could be due to a clogged or damaged burner orifice. Try cleaning the burner orifice. Another possible cause is a damaged gas regulator, which would need to be replaced.
What to do if my pleasant hearth VFS-PH30DT Wood stove burner(s) does not light after ODS/pilot is lit?
If the burner(s) on your pleasant hearth Wood stove does not light after the ODS/pilot is lit, the burner orifice might be clogged. Try cleaning the burner orifice.
What to do if my pleasant hearth VFS-PH30DT has a gas odor even when the control knob is in the OFF position?
If you smell gas from your pleasant hearth Wood stove even when the control knob is in the OFF position, there may be a gas leak. Locate and correct all leaks.
Why is there a spark at ODS/ pilot but no ignition when I press the ignitor button on my pleasant hearth VFS-PH30DT Wood stove?
If there's a spark at the ODS/pilot but no ignition when you press the ignitor button on your pleasant hearth Wood stove, first, ensure the gas supply is turned on and the equipment shutoff valve is open. Make sure the control knob is fully pressed in while pressing the ignitor button and that it's in the PILOT position. If the unit was just installed, there may be air in the gas lines; continue holding down the control knob and repeat the igniting operation until the air is removed. Also, the gas regulator setting may not be correct, in that case replace the gas regulator.
Covers essential safety warnings regarding operation, fuel use, and appliance placement.
Defines the qualifications and responsibilities of an agency for installation and service.
Explains the critical need for adequate air supply for safe and proper heater operation.
Worksheet and instructions for determining the necessary fresh air volume for the installation space.
Covers safety, heater placement, qualified installation, and intended use as supplemental heat.
Specifies minimum safe distances from the heater to surrounding combustible surfaces.
Details requirements for external regulators and illustrates gas supply line connections.
Methods for testing gas supply piping and heater connections for leaks using soap and water.
Crucial safety steps, including smelling for gas, before attempting to light the pilot.
Step-by-step instructions for safely igniting the pilot light using the electronic ignitor.
Diagnosing and correcting issues with spark generation and pilot ignition.
General| Maximum BTU Output | 30, 000 BTU |
|---|---|
| Material | Steel |
| Flue Size | 6 inches |
| Fuel Type | Wood |
| EPA Certified | Yes |
To Next Page