pleasant hearth PBAR-2427 User Manual

Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 877-447-4768 8:30 a.m. – 4:30 pm CST, Monday – Friday.
or email us at customerservice@ghpgroupinc.com
Wood Stove Blower Installation
and Operating Instructions
60-10-007     PrintedinChina Rev.1/10
For installation with
Pleasant Hearth Wood Stove
W a r m i n g Y o u r H o m e. W a r m i n g Y o u r H e a r t.
MODEL/MODELE/MODELO #PBAR-2427
8280 Austin Avenue
Mo r t on Grove, I L .
6 0 0 5 3 - 3 2 0 7
Tel: ( 847 ) 324 - 5900
Fax: ( 847 ) 324 - 5901
Toll Free (877) GHP Group
( 8 7 7 ) 4 4 7 - 4 7 6 8
www.ghpgroupinc.com
GHP
Wood Stove Blower Information
This blower is a reciprocating type blower. It is designed to direct heated air radiating from the rear of the stove to the
front at a low velocity. DO NOT expect a large volume of air to be felt when standing in front of the stove.
The blower is NOT thermostatically controlled. The blower speed is manually controlled by rotating the speed control
knob until the desired speed is achieved. When turned on, the rst setting will be “LOW”. “HIGH” setting may be
obtained by rotating the speed control knob clockwise.
Operating Voltage is 110 to 120 VAC at 60 Cycle.
WARNING!
DO NOT submerge the blower into any
liquids. This will create an electric shock
hazard. Unplug the blower before clean-
ing or performing any maintenance.
IMPORTANT : Ensure the blower and
gasket are oriented correctly. The blower
wheel and gasket cut-ot must align with the
cut-out in the rear heat shield. Fasten the
blower and gasket to the rear heat shield
using the four (4) screws provided.
DO NOT over tighten screws. Be sure to
plug the blower into a 3 prong gounded
outlet. DO NOT tamper with the grounding
prong on the cord.
IMPORTANT : When refuelling your
stove, turn the blower off for approximately
30 minutes. The stove will require time to
reach the required temperature for proper
combustion.
Installation
The blower is to be installed at the rear of the stove,
on the rear heat shield. Align the blower and gasket
mounting holes with those on the rear heat shield.
Cleaning
Periodic cleaning of the blower is recommended. Dust
or dirt accumulation could signicantly restrict airow.
Restriction in airow will reduce the efciency of the
blower and possibly damage the motor.
CAUTION: Extreme caution is
necessary when any fan is used by or
near children or invalids and whenever
the fan is left operating unattended.
Wood Stove manual drawing
Back of Stove
Gasket
Blower
Screws
Speed Control Knob
Electrical Cord
120V AC

pleasant hearth PBAR-2427 Specifications

General

Brand	pleasant hearth
Model	PBAR-2427
Category	Wood stove
Language	English

Summary

Wood Stove Blower Information

Refuelling Stove Operation

Turn blower off for 30 minutes when refuelling to allow stove to reach proper temperature for combustion.

Blower and Gasket Installation

Align blower wheel and gasket cut-out with rear heat shield cut-out. Fasten with provided screws. Plug into grounded outlet.

Electrical Shock Hazard Warning

Do not submerge blower in liquids. Unplug before cleaning or maintenance to prevent electric shock.

Fan Safety Caution

Use extreme caution with fans near children or invalids, and never leave the fan operating unattended.

Installation and Cleaning Instructions

Blower Installation Procedure

Install blower at the rear of the stove on the heat shield, aligning mounting holes with the shield.

Blower Cleaning and Maintenance

Periodic cleaning is recommended to prevent dust accumulation that restricts airflow and may damage the motor.