Polk Audio SWA500 User Manual

www
.PolkAudio.com
/ 800.377.7655 (USA & Canada) / 410.358.3600 (W
orldwide)
1
CSW100
Custom Install Subwoofer
The CSW100 subwoofer is a bandpass design with slot-load venting and has a 10 inch long-throw driver. The
CSW100 fits standard joist spacing and is designed specifically for floor and ceiling installation, or custom enclos-
ures that are at least nine inches (9”) deep. All sound comes from an opening approximately 13 inches long by 3
inches wide. There is an access panel on the back of the subwoofer should the driver have to be removed for service.
Hardware (included)
• 1 Subwoofer
• 4 Mounting Brackets
• 16 - 3/4" Particle Board Panhead Screws
• 16 Washers
• 3 Isolation Pads
• 1 Registration Card
• 1 Owner’s Manual (also available online)
• Plastic molded grille
• 6 Rubber Buttons (to cover grille screw holes)
Protective Cover
A 1/2" thick protective cover of MDF covers the
CSW100 grille opening. This protective cover
(3 - 1/4" x 13") is also the template you will use to
cut the grille opening. Affixed to the MDF cover
is the following label:
If you choose to use another grille, use one
that doesn’t resonate and caulk it.
Isolation
Pads
Mounting
Brackets
and Screws
Wood Joist
Wood Joist
Top View
of CSW100
Subwoofer
in floor
Available Finishes: Black
THIS DOCUMENT APPLIES TO CSW100, CSW200, AND SWA500 PRODUCTS
All the bass
comes out
of here!

Polk Audio SWA500 Specifications

General

Connectivity	Wireless
Driver Size	10 inches
Enclosure Type	Bass Reflex
Inputs	RCA
Type	Subwoofer
Amplifier Type	Built-in Class D

Summary

CSW100 Custom Install Subwoofer Overview

CSW100 Included Hardware

Lists the components and accessories included with the CSW100 subwoofer.

CSW100 Protective Cover Details

Describes the MDF protective cover for the CSW100, serving as a template.

CSW100 Dimensions and Specifications

CSW100 Dimensions

Provides detailed measurements and installed weight for the CSW100 subwoofer.

CSW100 Performance and Connections

Details the driver complement, power handling, frequency response, and connection types.

CSW100 Recommended Configuration and Support

Offers advice on amplifier pairing and provides factory support contact information.

CSW200 High Performance Subwoofer Introduction

CSW200 Included Hardware

Lists the components and accessories included with the CSW200 subwoofer.

CSW200 Grille Information

Provides recommendations for selecting and installing a grille for the CSW200.

CSW200 Protective Cover and Installation

Details the MDF protective cover for the CSW200 and its installation context.

CSW200 Dimensions and Specifications

CSW200 Dimensions

Provides detailed measurements and installed weight for the CSW200 subwoofer.

CSW200 Performance and Connections

Details the driver complement, power handling, frequency response, and connection types.

CSW200 Recommended Configuration and Support

Offers advice on amplifier pairing and provides factory support contact information.

SWA500 High Performance Subwoofer Amplifier

SWA500 Dimensions and Weight

Provides chassis dimensions, installed, and shipping weight for the SWA500 amplifier.

SWA500 Performance Specifications

Details continuous power, peak power, bandwidth, distortion, and crossover settings.

SWA500 Protection and Connections

Outlines protection circuitry, accessories, and speaker/line connection options.

SWA500 Recommended Configuration and Support

Explains SPEX card usage for matching and provides factory support contact details.