Why is my Porkka Refrigerator evaporator icing up?
If the evaporator ices up in your Porkka Refrigerator, and the cabinet starts to warm, it might be due to blocked air circulation to the condenser. Ensure nothing is obstructing the airflow. Another possible cause is a dirty or blocked condenser or condenser filter. Try cleaning the filter and/or the condenser to resolve this issue.
What to do if my Porkka Refrigerator compressor does not start?
If the compressor in your Porkka Refrigerator isn't starting and the unit isn't getting cold, there could be a few reasons. First, check if there's voltage at the compressor points; if not, the board might need replacing. Alternatively, the relay or the compressor itself may be defective, requiring replacement of the relay unit and/or the compressor.
What to do if my Porkka Refrigerator gives HA or LA temperature alarm?
If your Porkka Refrigerator is showing a 'HA' or 'LA' temperature alarm, it indicates that the control probe P1, responsible for monitoring the temperature inside the cabinet, may not be functioning correctly. The suggested solution is to replace the P1 probe.
What to do if my Porkka C Refrigerator gives Csd alarm?
If your Porkka Refrigerator is displaying a 'Csd' alarm, the fan might be out of order, requiring replacement. Another possible cause is a defective board, which would also need to be replaced.
What to do if the fan signal LED in the control device is on but the evaporator fan does not rotate in my Porkka C?
If the fan signal LED is on but the evaporator fan isn't rotating in your Porkka Refrigerator, it could mean that the fan is broken and needs to be replaced. Alternatively, the board might be defective and also needs replacing.
Why is probe alarm P1, P2, or P3 shown on my Porkka C Refrigerator display?
If you're seeing a probe alarm (P1, P2, or P3) on your Porkka Refrigerator's display, it could be due to a couple of reasons: either the probe cable has detached from the card connectors, in which case you should reattach the cable, or the probe cable itself is broken, requiring you to replace the probe.
What to do if the fan signal LED in the control device is not on and the evaporator fan does not rotate in my Porkka C?
If the fan signal LED in the control device is not illuminated and the evaporator fan isn't rotating in your Porkka Refrigerator, it could be due to a malfunctioning evaporator probe P2, which would need replacement. Another potential cause is a faulty door switch, which would also require replacement.
General warnings and safety precautions for the controller.
Key settings for temperature control and load management.
Identifies common probe and temperature-related fault messages.
Diagnosing problems related to temperature probes.
Identifying causes for high/low temperature warnings.
Troubleshooting fan not running or signal LED problems.
Diagnosing faults with the door opening detection.
Addressing fan motor failure or control board defects.
Troubleshooting condenser fan and associated board problems.
Identifying causes of icing and cabinet air leaks.
Resolving problems related to condenser blockage or dirty filters.
Troubleshooting specific evaporator fan operational faults.
Diagnosing problems with hot-gas and electric defrost systems.
Troubleshooting why the compressor does not start or cool.
General warnings and safety precautions for the controller.
Key settings for temperature control and load management.
Identifies common probe and temperature-related fault messages.
Diagnosing problems related to temperature probes.
Identifying causes for high/low temperature warnings.
Troubleshooting fan not running or signal LED problems.
Diagnosing faults with the door opening detection.
Addressing fan motor failure or control board defects.
Troubleshooting condenser fan and associated board problems.
Identifying causes of icing and cabinet air leaks.
Resolving problems related to condenser blockage or dirty filters.
Troubleshooting specific evaporator fan operational faults.
Diagnosing problems with hot-gas and electric defrost systems.
Troubleshooting why the compressor does not start or cool.
General| Category | Refrigerator |
|---|---|
| Capacity | Unknown |
| Energy Class | Unknown |
| Freezer Capacity | Unknown |
| Noise Level | Unknown |
| Height | Unknown |
| Width | Unknown |
| Depth | Unknown |
| Weight | Unknown |
To Next Page