EasyManua.ls Logo

Porter-Cable BSV750 - User Manual

Porter-Cable BSV750
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instruction
manual
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
Part No. D29525-038-0
ESPAÑOL: PÁGINA 25
FRANÇAIS: PAGE 49
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
Model
BSV750
Copyright © 2003 Porter-Cable Corporation
The Model and Serial No. plate is located on the frame.
Record these numbers in the spaces below and retain for
future reference.
Model No.
Type
Serial No.
Generator
Shown with optional portability kit

Table of Contents

Questions and Answers

  • K
    Kathleen FloresAug 12, 2025
    Why won't my Porter-Cable BSV750 start?
    • A
      ashleylopezAug 12, 2025
      Several issues may prevent the Porter-Cable Portable Generator engine from starting. Check if the fuel or oil levels are low and add fuel or oil as needed. Ensure the ignition switch is in the 'ON' position. Inspect the spark plug for faults and replace if necessary. Adjust the choke to the correct position. Verify that the fuel shut-off valve is open. Remove any load from the unit during start-up. Finally, make sure the spark plug wire is securely attached to the spark plug.
  • C
    Christopher SullivanAug 16, 2025
    What to do if my Porter-Cable BSV750 has no electrical output?
    • H
      Heather JonesAug 16, 2025
      If your Porter-Cable Portable Generator has no electrical output, the receptacle may be faulty and require replacement by a service center. Check if the circuit breaker has tripped and reset it. A defective capacitor could also be the cause, requiring replacement by a service center. Inspect the power cord for faults and repair or replace it. Additionally, check if the GFCI switch breaker has tripped and reset it.
  • K
    knguyenAug 20, 2025
    Why does the circuit breaker keep tripping on my Porter-Cable BSV750?
    • M
      Matthew ChristensenAug 20, 2025
      Repeated circuit breaker tripping in your Porter-Cable Portable Generator can be due to an overload. Try reducing the load on the generator. It can also be caused by faulty cords or equipment. Check your cords and equipment for damaged, bare, or frayed wires and replace them if necessary.
  • A
    Anna RiosAug 23, 2025
    Why is my Porter-Cable Portable Generator overheating?
    • B
      Brett WilliamsAug 25, 2025
      Your Porter-Cable Portable Generator may be overheating because it is overloaded. Try reducing the load. Insufficient ventilation can also cause overheating, so move the generator to a location with an adequate supply of fresh air.
  • J
    John NelsonAug 27, 2025
    What to do if DC does not have power with the circuit breaker depressed on Porter-Cable BSV750 Portable Generator?
    • J
      Jennifer PowellAug 27, 2025
      If the DC power on your Porter-Cable Portable Generator does not work with the circuit breaker depressed, the rectifier, windings in stator, or wire harness might be faulty. Have a service center replace the faulty component.
  • A
    Andrew BlakeAug 31, 2025
    What causes no auto idle in Porter-Cable Portable Generator?
    • J
      jamesperezAug 31, 2025
      If your Porter-Cable Portable Generator has no auto idle, the solenoid, idle control switch, windings in stator, circuit board, or wire harness might be faulty. Have a service center replace the faulty component.
  • D
    David CookSep 4, 2025
    What to do if my Porter-Cable Portable Generator has no electrical output and the circuit breaker keeps tripping?
    • S
      schroederlindaSep 4, 2025
      If your Porter-Cable Portable Generator has no electrical output and the circuit breaker is tripping repeatedly, it could be due to a faulty receptacle, the circuit breaker kicking out, a defective capacitor, a faulty power cord, or the GFCI switch breaker kicking out due to overload or faulty cords/equipment. You can try to depress and reset the circuit breaker. Also reduce the load and check for damaged, bare, or frayed wires on equipment and replace if necessary. For a faulty receptacle or defective capacitor, have an Authorized Service Center replace them. Repair or replace the cord if it's faulty.
  • I
    Ian WilliamsSep 7, 2025
    How to fix overheating, no auto idle, and no DC power on my Porter-Cable Portable Generator?
    • K
      Katie CainSep 8, 2025
      If your Porter-Cable Portable Generator is overheating, has no auto idle (if equipped), and the DC does not have power with the circuit breaker depressed (if equipped), it could be due to several reasons. Overheating can be caused by the generator being overloaded or insufficient ventilation. The lack of auto idle may be due to a faulty solenoid, idle control switch, windings in stator, circuit board, or wire harness. The lack of DC power may be due to a faulty rectifier, windings in stator, or wire harness. To address overheating, reduce the load and move the generator to an area with adequate fresh air. For the other issues, have a Service Center replace the faulty components.

Summary

Generator

Consumer General and Service Information

Consumer Safety Information

Safety Guidelines and Definitions

Important Safety Instructions

Generator Specifications

Generator Assembly

Remove Generator from Carton

Instructions for unpacking the generator from its shipping carton.

Other Loose Parts

Details about other components included with the generator.

Grounding the Generator

Information on how to properly ground the generator according to electrical codes.

Typical Battery Installation

Obtaining Electricity from Generator

Extension Cords

Guidelines for selecting and using appropriate extension cords with the generator.

Double Throw Transfer Switch

Instructions and warnings regarding the safe use of a transfer switch.

Generator Operation

Generator Controls and Features

Overview of generator controls, capacity, and safety features.

Low Oil Protection

Explanation of the low oil shutdown safety feature.

12 V DC Outlet Usage

Before Start Up Procedures

How to Start the Engine

How to Stop the Engine

Connecting Electrical Loads

Generator Maintenance

Maintenance Responsibilities and Schedule

Overview of user's maintenance tasks and schedule.

Engine and Generator Care

Instructions for engine and generator unit maintenance.

GFCI Receptacle Testing

Procedure for testing the Ground Fault Circuit Interrupter (GFCI) receptacle.

Generator Storage

Engine Preparation for Storage

Steps to prepare the engine for long-term storage, including fuel stabilizer.

Generator and Battery Storage

Cleaning the generator and storing the battery according to manufacturer guidelines.

Wattage Calculations

Determining Wattage Requirements

Guide to calculate total running and starting wattage for connected appliances.

Starting Wattage Requirements

Household Wattage Calculator

Troubleshooting Guide

Limited Warranty

Notes Section

Quick Facts

Porter-Cable BSV750 Specifications

General IconGeneral
BrandPorter-Cable
ModelBSV750
CategoryPortable Generator
LanguageEnglish

Related product manuals