To Next PageTo Next PageWhy is the cutting head on my Powerplus Trimmer hard to turn?
If your Powerplus Trimmer's cutting head is hard to turn, it's likely due to grass wrapping around it. To resolve this, clean the affected parts of the machine to remove any grass buildup.
How to fix line that will not advance on Powerplus Trimmer?
If the line on your Powerplus Trimmer will not advance, you can try several solutions: * Lubricate it with a silicone spray. * Replace the spool. * Remove the spool and feed the line out manually. * Remove the line from the spool and rewind it.
Why does grass continually wrap around the shaft of my Powerplus Trimmer?
If grass continually wraps around the shaft and trimmer head assembly of your Powerplus Trimmer, it may be because you are cutting tall grass at ground level. To prevent this, cut tall grass from the top down.
The Powerplus POWXG30035 is a high-quality electric grass trimmer designed for trimming and finishing lawn edges and for cutting grass in confined spaces. It is not intended for commercial use. This corded power tool operates on a 230V, 50Hz power supply and has a rated power of 600W. It achieves a no-load speed of 7500 min⁻¹ and offers a cutting width of 350 mm. The trimmer uses a 1.6 mm diameter cutting line and features an intelligent two-line cutting system. Weighing 2.6 kg, it is designed for ease of use and maneuverability.
The POWXG30035 is a Class II double-insulated machine, meaning no earthing wire is necessary. It complies with essential safety standards of applicable European directives. Several safety symbols are used in the manual to highlight important precautions. Users are warned about the risk of personal injury or damage to the tool and are advised to read the manual before use. Hands and feet should be kept away from sharp parts, and gloves should be worn during operation. The trimmer should never be operated in the rain or in damp/wet conditions, as moisture poses an electrical shock hazard. Ear guards and goggles are mandatory to protect against noise and flying debris. Bystanders, children, and animals must be kept at a safe distance from the working area.
A crucial safety feature is the requirement to connect the appliance only to an electric circuit protected by an earth leakage switch (30 mA). Before each use, the appliance and extension cord should be checked for damage or wear. If damaged, the mains cable must be immediately removed from the wall socket, and the cable should not be touched before disconnection. The trimmer must always be used with the safety guard properly in place; operating it without the guard can cause the motor to overheat and void the warranty. The guard itself has a very sharp cutting edge for the nylon line, requiring careful handling during assembly.
Users are advised to stay alert, watch what they are doing, and use common sense. The tool should not be used when tired or under the influence of drugs, alcohol, or medication. Eye protection is always required, and other safety equipment like dust masks, non-skid safety shoes, and hard hats should be used when needed. Accidental starts are to be avoided by ensuring the switch is in the off position before inserting the plug. Any adjusting keys or spanners must be removed before turning on the power tool. Users should not overreach and must keep their feet firmly on the ground for control. Proper attire, avoiding loose clothing or jewelry, is essential to prevent entanglement with moving parts. If dust extraction and collection facilities are present, they should be attached and used correctly.
The power supply must match the voltage on the rating plate. Power tool plugs must match the outlet, and adapter plugs should not be used with earthed power tools. Contact with earthed surfaces like pipes, radiators, and refrigerators should be avoided. The power cord must not be damaged, used for carrying or pulling the tool, or allowed to come into contact with heat, oil, sharp edges, or moving parts. If operating in a damp location is unavoidable, a residual current device (RCD) must be used.
The trimmer should be used only for its intended purpose. If the switch is broken, the tool must be repaired. The plug should be disconnected from the power source before making adjustments, changing accessories, or storing the tool. When not in use, the trimmer should be stored out of reach of children and untrained individuals. Regular maintenance is crucial, including checking for misalignment, jammed parts, or breakages. Cutting tools should be kept sharp and clean. The tool, accessories, and cutting tools must be used in accordance with the instructions and intended manner, considering working conditions and the task at hand.
Only stout shoes or boots and long trousers should be worn to protect feet and legs. The appliance should only be used in daylight or with good lighting. Before use, sticks, stones, wire, and other obstacles must be removed from the working surface. The trimmer should only be used in an upright position with the cutting line pointing to the ground. Hands and feet must always be kept away from the cutting line, and the mains cable should not touch the cutting line. After switching off, the cutting line continues to rotate for a short time; users must wait for it to come to a complete standstill before putting the appliance down and should never attempt to stop it manually. Only the manufacturer-recommended type of cutting line should be used; metal cutting lines or fishing lines are prohibited. The plug should be removed from the wall socket after use, before servicing, or when the appliance is not in use. The trimmer should not be used to cut against hard objects or grass not in contact with the ground (e.g., on walls or rocks).
The trimmer requires some assembly. The safety guard and edger wheel are fixed to the trimmer head using four provided screws, ensuring the sides are located in the grooves. The auxiliary handle assembly involves pushing its knobs, sliding the handle onto the handle bracket assembly on the trimmer's shaft, and then releasing the knobs to lock it. The auxiliary handle's bracket can be moved up or down the shaft, and the handle itself can be moved into five different locked positions by pushing the knob, allowing for adjustment to the desired height.
To switch on, the On/Off trigger (1) is pressed; releasing it switches the trimmer off. If the nylon line is too short, the trimmer should be run for a few seconds while touching the working area to allow the line to lengthen and be cut to the correct length. The trimmer should not be overloaded; cutting in small sections at high speed improves efficiency. The edge of the guard can be used as a guide when cutting near fences and walls. The telescopic shaft length can be adjusted by unscrewing the height adjustment locking collar, sliding the shaft to the desired height, and then screwing the collar to fix it.
To transform the trimmer into an edger, the device must first be switched off and disconnected from the power mains. The rotation locking collar (4) is lifted, and the top of the shaft is turned 180° counter-clockwise (the head moves in one direction only). Releasing the rotation locking collar locks the shaft in place, allowing the trimmer to be used as an edge trimmer. A cable strain relief hook is provided to reduce strain on the cable inlet by forming a loop and locating the cable around it.
Upon initial startup, a small length of line is fed out, producing a "clattering" noise as the lines hit the line cutter. This is normal and will reduce as the line is cut to the correct length and the motor reaches full speed. If the cutting noise is not heard, more line will be fed out. The trimmer features an intelligent line feed system that automatically feeds more line when needed or when the line encounters resistance, eliminating the need to stop the machine. It is important to ensure line is fed out before operation and that the motor is at full speed before trimming. Only 1.60mm diameter cutting line should be used; other sizes or materials like wire, string, or rope can cause improper cutting head function, serious injury, or become dangerous missiles.
Common issues and their solutions include:
The noise emission values measured according to relevant standards are: Acoustic pressure level (LpA) of 85 dB (A) and Acoustic power level (LwA) of 92 dB (A). Users are advised to wear hearing protection when sound pressure exceeds 85 dB(A). The vibration level (aw) is 4.60 m/s².
The tool is designed for long-term operation with minimal maintenance, but continuous satisfactory operation depends on proper care and regular cleaning. Before any maintenance, the tool must be switched off and unplugged. Regular cleaning of the ventilation slot with a soft brush or dry cloth is recommended. The cutting line and spool should also be cleaned regularly with a soft brush or dry cloth. A blunt scraper should be used to remove grass and dirt from the underside of the guard.
This product comes with a 36-month warranty from the date of purchase by the first user. The warranty covers material or production flaws but excludes batteries, chargers, defective parts subject to normal wear and tear (bearings, brushes, cables, plugs), or accessories (drills, drill bits, saw blades). Damage or defects resulting from maltreatment, accidents, alterations, or transportation costs are not covered. Inappropriate use, including not following manual instructions, inexpert assembly, lightning strikes, or erroneous net voltage, also voids the warranty. The manufacturer disclaims liability for bodily injury from inappropriate tool use. Repairs must be carried out by an authorized Powerplus service center. The warranty period is not prolonged by claims or device replacements. Replaced devices or parts remain the property of Varo NV. Claims may be rejected if purchase cannot be verified or if the product has not been properly maintained. The purchase receipt serves as proof of date of purchase. The appliance must be returned undismantled, in an acceptably clean state (in its original blow-moulded case if applicable), with proof of purchase. Further information can be obtained by calling 00 32 3 292 92 90. Transportation costs are borne by the customer unless otherwise agreed. Claims are not valid if damage results from negligent maintenance or overload. Exclusions include fluid permeation, excessive dust penetration, intentional damage, inappropriate usage, incompetent usage, inexpert assembly, lightning strike, and erroneous net voltage.
When the appliance needs replacement after extended use, it should not be disposed of with household rubbish. Instead, it should be disposed of in an environmentally safe way. Electrical machine items should be recycled where facilities exist. Users should check with their local authority or retailer for recycling advice.
General