Precor 600 Series - User Manual

600 Line Upright Bike (UBK) Assembly Guide
To assemble the equipment, follow the steps in the order listed in this assembly guide. For more product information, visit us at www.precor.com.
WARNING
At least two people are required to assemble the equipment. DO NOT attempt assembly
by yourself.
Seat
Rear stabilizer
Upright Support
Bottle holder
Handle bars
Console
mount
Front stabilizer
We recommend you:
▪ Assemble the equipment close to where you plan to use it.
▪ Assemble the equipment on a solid, at surface, so that it remains level and stable.
▪ Locate the equipment at least 19.7 inches (0.5 meter) away from walls or furniture on either side of the
equipment, and 19.7 inches (0.5 meter) away from objects behind or in front of the equipment.
▪ DO NOT move the equipment without assistance.
Required tools and hardware
For hardware, the US English acronym is used throughout the guide and in all localized versions.
Tools Component Description Quantity Component Description Quantity
▪ 6 mm hex wrench
▪ 10 mm hex wrench
▪ 5/32-inch hex wrench
▪ 13 mm open-end, box or
socket wrench
▪ 17 mm open-end wrench
▪ #2 Phillips screwdriver
▪ Wire cutter
▪ Fish tape
Socket head cap screw
(SHCS) / M12 x 80 mm
2 Pan head cap screw
(PHCS) / M5 x 12 mm
2
Socket head cap screw (SHCS) /
M8 x 25 mm
4 Washer, zinc / 8.2 mm 3
Button head cap screw (BHCS) /
M10 x 40 mm
4 Washer, black / 8.1 mm 4
Plug for access hole on upright
support
1 Nylon lock nut / M8 3
Attach the stabilizers
NOTE
The front stabilizer has two wheels. These wheels help to move the location of
the bike.
Figure 1
Figure 2
To attach the stabilizers:
1. Place the rear stabilizer under the bracket at the rear of the bike (Figure 1).
2. Attach the rear stabilizer using two M10 x 40 mm BHCS. Fully tighten the screws using a
6 mm hex wrench (Figure 2).
3. Place the front stabilizer underneath the bracket at the front of the bike (Figure 3).
4. Secure the front stabilizer using two M10 x 40 mm BHCS. Fully tighten the screws using
a 6 mm hex wrench (Figure 4).
Figure 3 Figure 4
To attach the seat:
1. Place the seat on the bracket so that the three bolts extend through the screw holes.
2. Attach an 8.2 mm washer and M8 Nylon lock nut to each bolt. Fully tighten the fasteners using a 13 mm
socket wrench.
Figure 5

Summary

Required Tools and Hardware

Attach Stabilizers

Attach Rear Stabilizer

Secure the rear stabilizer using two M10 x 40 mm BHCS with a 6 mm hex wrench.

Attach Front Stabilizer

Secure the front stabilizer using two M10 x 40 mm BHCS with a 6 mm hex wrench.

Attach Seat

Install Seat Bolts and Nuts

Attach seat with bolts, 8.2 mm washer, and M8 Nylon lock nut, tightening with a 13 mm socket wrench.

Attach Upright Support and Cables

Route Console Cables

Feed console and power cables through the upright support and secure them.

Connect Upright Support

Position upright support over channel and secure with M12 x 80 mm SHCS using a 10 mm hex wrench.

Attach Handlebars

Route Heart Rate Cable

Thread heart rate cable through upright support arm and out to console mount.

Secure Handlebars

Attach handlebars to upright support using four screws and washers with a 6 mm hex wrench.

Attach Bottle Holder

Mount Bottle Holder

Secure bottle holder to upright support using M5 x 12 mm PHCS with a Phillips screwdriver.

Level the Equipment

Adjustable Feet

Adjust feet by turning clockwise or counterclockwise to ensure stability and contact with floor.

Precor 600 Series Specifications

General

Brand	Precor
Model	600 Series
Category	Exercise Bike
Language	English