Precor Resolute RSL 314 Maintenance Guide

©2019 Precor Inc. | Resolute™ Strength Selectorized Line | Maintenance Guide
2
This guide provides information about items that need to be inspected and maintained on a daily,
weekly, monthly, and annual basis.
• Precor recommends owners implement a thorough maintenance program that incorporates
regular safety inspections by qualied maintenance technicians as outlined in this mainte-
nance guide.
• Precor recommends that service technicians thoroughly read and understand the safety
guidelines and maintenance procedures covered in this guide.
• Owners should not attempt to service the strength equipment, except for the maintenance
tasks described in this guide.
• During maintenance, place an “Out Of Order” sign on the equipment.
• For torque settings, review the product Assembly Guide included with your equipment or
visit www.precor.com.
Important It is the duty of the owner to maintain equipment in accordance with the instructions
in this material and any accompanying material. Always purchase replacement parts and hard-
ware from Precor. Using parts not approved by Precor will void the Precor Limited Warranty and
may cause serious injury. Order parts from Precor Customer Service at www.pr ecor.com.
Recommended Tools
• Torque wrench with torque range to at least 150 ft-lb (206 N-m) and ts the following hex
bits: 6, 8, and 10 mm
• Socket wrench sets, metric and standard, plus extensions
• Open-end wrench sets, metric and standard
• Hex wrench sets, metric and standard, plus extensions
• Retaining ring pliers, large, medium, and small
Daily Maintenance Tasks
Stability
Verify all equipment feet sit squarely on the oor.
Upholstery
Inspect upholstery pads for cracks in the pads, broken and loose stitching, loose staples and loose
mounting bolts. Replace pads as needed with Precor approved upholstery pads. To remove surface
dirt and perspiration, clean upholstery daily with a mild soap and water solution in a spray bottle.
Spray upholstered surfaces lightly and wipe dry with a clean cloth.
Important To clean the upholstery, DO NOT use cleaning products that have any of these ingre-
dients: solvents, alcohol, ammonia, or petroleum. Use a mild detergent-based cleaner instead.
Frame
To remove grease and dirt, spray the frame daily with a mild soap and water solution and wipe dry
with a clean cloth. As you clean, inspect the frame for cracks, rust, or other damage. Make sure welds
are solid and fasteners are properly secured.
To restore and maintain the luster of chrome parts, use a commercial chrome cleaner.
Fasteners and hardware
Fasteners can loosen with normal use. Inspect all nuts, bolts, screws, and other fasteners to make
sure they are tight and installed correctly. Check fasteners at bolted joints to make sure the connec-
tions are secure. If a fastener is loose but in good condition, retighten it.
If you are concerned about the integrity of the fastener, remove it, clean the threads, and inspect it
for any damage such as cracks, bad threads, corrosion, or rust.
Reinstall the fastener if it appears to be in good condition. Otherwise, remove the equipment from
service until a new fastener can be installed properly. Contact Precor Customer Support to order new
parts at www.precor.com.
Important Fastener quality and specications vary considerably. Replace only with the Precor
approved fastener specically engineered for the precise application. Failure to do so will void the
Precor Limited Warranty.
Shroud
CAUTION To avoid damage to the shrouds, clean them according to the instructions in this
section. Use a clean, non-abrasive cloth and light pressure to avoid scratching the surface.
To clean the shrouds, Precor recommends mixing a few drops of mild dishwashing liquid in a gallon
of water and using it to wipe the equipment with a soft cloth. Wipe the soap off using another soft
cloth and clean water. The shrouds are easily scratched and damaged through improper cleaning
techniques. To avoid problems, dust the shrouds often with a clean, lint-free cloth and light pressure.
Avoid rubbing dirt or grit into the surface.
Important DO NOT use ketones, aromatics, esters, window cleaning sprays, alcohol, kitchen
scouring compounds, ammonia-based cleaning solutions or solvents (such as acetone, benzene,
gasoline, carbon tetrachloride, or thinners).
Cables and end connections
CAUTION Carefully inspect the cables, pulleys, fasteners, and related hardware regularly.
Replace any cable at the rst sign of wear using only Precor-supplied replacement parts. With
regular use, a cable can become worn and might fail. Sudden failure of a worn cable can cause
severe injury to a user. Contact Precor Customer Support to purchase replacement parts.
Inspect the cables and end connections each day, and replace if damaged. Check for kinks, frayed
wires, or deterioration of the cable coating. Look for signs of wear particularly at crimped ends of the
cable and near pulleys.
Important Cables must be replaced immediately if they are damaged to avoid possible injury to
users.
Some obvious signs of cable damage are:
Exposed inner wire, stretching or cuts in the coating, or broken coating in the area that passes
over a pulley.
A zigzag or wavy pattern.
Kinks, which may indicate internal damage.
A necked-down cover.
A “ballooned” cover.
1
2
4
3
5

Precor Resolute RSL 314 Specifications

General

Brand	Precor
Model	Resolute RSL 314
Category	Elliptical Trainer
Language	English