EasyManua.ls Logo

Prem-I-Air PAC1140 - User Manual

Prem-I-Air PAC1140
22 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
M
M
O
O
B
B
I
I
L
L
E
E
A
A
I
I
R
R
C
C
O
O
N
N
D
D
I
I
T
T
I
I
O
O
N
N
E
E
R
R
(
(
w
w
i
i
t
t
h
h
H
H
e
e
a
a
t
t
p
p
u
u
m
m
p
p
)
)
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
M
M
A
A
N
N
U
U
A
A
L
L
Model PAC1130 (10,000 BTU/HR)
Model PAC1140 (14,000 BTU/HR)
IMPORTANT
Please read these instructions carefully and retain for
future use.

Table of Contents

Questions and Answers

  • D
    David WallaceAug 5, 2025
    What to do if Prem-I-Air Air Conditioner does not work?
    • R
      Rebecca AdamsAug 5, 2025
      If your Prem-I-Air Air Conditioner isn't working, check the following: * Ensure the unit is properly plugged into a socket outlet. * If the plug or socket is faulty, contact a qualified engineer for replacement. * Check the fuse and replace or reset it if necessary. A power supply fault may be the reason: the unit may not be plugged in, the plug or socket could be faulty or the fuse might be blown or tripped.
  • J
    Jacob SmithAug 9, 2025
    What to do if LCD window of Prem-I-Air PAC1140 shows "E4"?
    • W
      William CoxAug 9, 2025
      If the LCD window on your Prem-I-Air Air Conditioner displays "E4", it indicates that the water tank is full. You should drain the condenser water.
  • A
    Arthur NguyenAug 13, 2025
    Why Prem-I-Air PAC1140 Air Conditioner display shows run mode but does not run?
    • B
      Brenda BurchAug 13, 2025
      The Prem-I-Air Air Conditioner might show the run mode but not start because the TIMER has been set. You can either cancel the TIMER or wait for it to initiate the program.
  • T
    Tina RileyAug 17, 2025
    Why Prem-I-Air Air Conditioner delivers no cold air?
    • R
      Ryan LeonAug 18, 2025
      If your Prem-I-Air Air Conditioner isn't delivering cold air, it could be due to frost on the evaporator. The unit is likely defrosting and will resume normal operation after defrost termination.
  • T
    tiffany16Aug 22, 2025
    What to do if LCD window of Prem-I-Air Air Conditioner shows "E2, E3"?
    • J
      James PalmerAug 22, 2025
      If the LCD window on your Prem-I-Air Air Conditioner displays "E2, E3", it indicates an issue with the room temperature sensor. Refer fault to authorised dealership.
  • H
    Hector SmithAug 27, 2025
    Why Prem-I-Air Air Conditioner delivers no cool air in dehumidifying mode?
    • A
      Amber ChaneyAug 27, 2025
      If your Prem-I-Air Air Conditioner isn't delivering cool air in dehumidifying mode, it's likely because there is frost on the evaporator. The unit is defrosting and will run after defrost termination. This is normal operation.
  • D
    Diane WilliamsonAug 31, 2025
    Why Prem-I-Air PAC1140 not working in cooling mode?
    • T
      Teresa PerryAug 31, 2025
      Your Prem-I-Air Air Conditioner might not be working in cooling mode because the room temperature is lower than the set temperature. This is normal.

Summary

Instruction Manual

Important Safety Instructions

BS Plug Wiring

Technical Specification

Use of Control Panel

Basic Operations

Covers turning the unit on/off, selecting modes, and adjusting temperature/fan speed.

Detailed Mode Operations

Explains Automatic, Dehumidification, Cooling, Fan, and Heat modes in detail.

Advanced Operations

Instructions for timer, swing, and sleep functions.

Remote Control Operation

Air Exhaust Duct Installation

Exhausting Hot Air Methods

Maintenance

Filter Maintenance

Drainage Tray Condensate Removal

Troubleshooting

Warranty

Warranty Information and Recording

Prem-I-Air PAC1140 Specifications

General IconGeneral
BrandPrem-I-Air
ModelPAC1140
CategoryAir Conditioner
LanguageEnglish

Related product manuals