Need help?Do you have a question about the Printronix P8000 Plus Series and is the answer not in the manual?
General| Print Technology | Line Matrix |
|---|---|
| Resolution | 180 x 144 dpi |
| Print Width | 13.6 inches |
| Paper Width | 3 to 17 inches |
| Operating Systems | Windows, Linux, UNIX |
| Power Requirements | 100-240 VAC, 50/60 Hz |
| Connectivity | Ethernet, Parallel, Serial, USB |
| Noise Level | 55 dB (operating) |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Emulations | IBM ProPrinter, Epson FX |
| Paper Handling | Continuous forms |
Provides a general overview of the printer and the conventions used within this manual.
Details on periodic cleaning, proper handling, and using correct printer supplies for optimal performance.
Information highlighted under special headings to draw attention to potential hazards or important operational details.
Lists other documents that provide additional information on printer setup, maintenance, and specific emulations.
Read this chapter carefully before installing and operating the printer for safety and equipment protection.
Specifies the necessary AC power supply voltage, frequency, and circuit protection for the printer.
Requirements for selecting a printer location, including clearance, power outlet, and environmental conditions.
Diagrams identifying the location of key printer components such as ribbon cartridge, tractors, and platen.
Describes the different operating modes: Online, Offline, Menu, and Fault, and how to navigate between them.
Illustrates the keys, displays, and indicators on the control panel and their functions.
Detailed descriptions and functions of each key on the printer's control panel.
Covers routine printer operating procedures such as reloading and unloading paper.
Step-by-step instructions for loading new paper into the printer without removing the existing paper.
Procedure for completely removing paper from the printer, including tearing off and removing from the supply area.
Explains the printer's feature for automatically monitoring and communicating ribbon life status.
Provides instructions for changing the ribbon cartridge, including determining print darkness preference.
Explains configuration as matching printer characteristics to host computer requirements and tasks.
Describes the organization of the Main Menu based on different firmware types available for the printer.
Details how to change printer parameters via control panel keys or host control codes.
Explains how to permanently store changed parameter settings as configurations in the printer's memory.
Provides instructions on how to navigate through the printer's configuration menus.
Details the menu structure and options available for the P8000 Standard Firmware.
Allows control of printer configurations according to specifications necessary for print jobs.
Enables selection and configuration of various interface types between the printer and host computer.
Allows configuration of options available for the current operating emulation.
Describes the configuration options specific to the P-Series emulation.
Details the features and configuration of the Intelligent Graphics Processor (IGP) using PGL.
Explains the Code V Graphics language (VGL) emulation features and configuration.
Contains settings for ZTP, Ribbon End Point, Bar Code Quality, Tear Bar Dist., and View Function.
Provides access to advanced operating parameters like PTX_SETUP, Hex Dump, and File System management.
Allows selection of Special Function Control Code for PTX_SETUP commands.
Describes the host interfaces provided with the printer and EMC requirements for cables.
Details the RS-232 serial interface characteristics, pin assignments, and data cable length.
Explains USB port functionality, buffer size, timeout settings, and its role in Auto Switching.
Provides pin assignments and signal descriptions for the Centronics parallel interface.
Describes the IEEE 1284 interface operating modes, compatibility, nibble, byte modes, and signals.
Explains how to reprogram the security key using an SPX module via the debug port.
Step-by-step instructions for programming the security key using the SPX module.
Describes the different firmware file types and their usage in download methods.
Instructions for downloading firmware using a web browser via the printer's IP address.
Steps for downloading firmware using the Windows driver via the printer's management interface.
Method for downloading firmware using an executable file without manual printer mode changes.
Procedure for downloading firmware using a specific key combination on the printer's control panel.
Detailed steps for downloading firmware to the printer through a USB port.
Explains how to utilize SD cards for downloading files, fonts, and configurations to the printer.
Describes how TrueType fonts can be downloaded to customize forms and labels.
Explains how to download, configure, execute, and terminate demo test files for printer functionality.
Guidelines for cleaning the printer's exterior and interior components periodically.
Provides guidance for fixing common printer problems and understanding error messages.
Lists common print quality issues and their corrective actions.
Summarizes fault messages, categorizes them as operator correctable or field service required, and provides solutions.
Details the yield specifications for various types of Printronix ribbon cartridges.
Provides specifications for paper type, thickness, sheet thickness, and drive tractor compatibility.
Lists the physical dimensions and weight for cabinet and open pedestal printer models.
Specifies the operating and storage temperature and relative humidity ranges for the printer.
Details the input voltage, frequency, amps, watts, and BTU/Hr for ASCII and H-Series models.
Introduces the P8000 Zero Tear Pedestal printer and its available models.
Describes how to position paper input and adjust paper guides for ZTP printer operation.
Step-by-step instructions for loading paper onto the printer's tractors.
Procedure for setting the tear bar distance for optimal tear-off positioning.
Instructions on how to set the top of form position using the SET TOF button.
Defines options for enabling/disabling ZTP features, tear bar distance, and auto present data time.
Discusses limitations related to forms type and potential paper jams on the ZT printer.
Explains the QCMC's ability to duplicate printer firmware, configurations, and custom files.
Instructions for installing or removing the QCMC, emphasizing powering off the printer first.
Procedure to capture printer firmware, configurations, and custom files onto the QCMC.
Steps to copy the captured QCMC image to another printer for identical configuration.
Introduces PTX_SETUP commands as a superset for printer tasks like configuration and data downloading.
Explains the design and functionalities of PTX_SETUP commands for line matrix printers.
Describes common PTX_SETUP commands supported across platforms and their general formation.
Provides contact information and required details for calling Printronix Customer Support.
Contact information for obtaining genuine Printronix supplies.
Lists the addresses and contact details for Printronix's global corporate offices.
General information regarding product offerings, intellectual property, and user responsibilities.
Includes FCC, European Union, and other regulatory compliance statements for the equipment.
Details the terms and conditions of the software license agreement for the printer.
To Next Page
