EasyManua.ls Logo

pro.point 8913204 - User Manual

pro.point 8913204
100 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
V1.0 8913204
Please read and understand all instructions before use. Retain this manual for future reference.
PRESSURE WASHER
GAS

Table of Contents

Questions and Answers

  • M
    matthewtranAug 10, 2025
    How to fix low pressure on my pro.point Pressure Washer?
    • C
      Cindy JenkinsAug 10, 2025
      If your pro.point Pressure Washer has low pressure, several factors could be the cause. First, ensure your water supply provides 2.5 GPM at 20 psi. Check for and remove any debris obstructing the nozzle or the water filter screen. Air in the hose can also cause low pressure; to resolve this, stop the engine and water source, disconnect the water source, turn it on to remove air from the hose, then reconnect and squeeze the trigger to remove remaining air. Finally, make sure the high-pressure hose is under 100 ft.
  • C
    Christopher YangAug 15, 2025
    Why is my pro.point Pressure Washer not drawing detergent?
    • M
      Michelle WilsonAug 15, 2025
      If your pro.point Pressure Washer isn't drawing detergent, several issues might be at play. First, make sure the spray gun is set to low pressure. Also, check the chemical filter for clogs and clean it if necessary. Ensure the chemical screen is fully submerged in the chemical solution. If the chemical solution is too thick, dilute it to the consistency of water. Avoid using an excessively long pressure hose; instead, lengthen the water supply hose. If there's chemical build-up in the chemical injector, have it cleaned or replaced by an authorized dealer.
  • J
    John SilvaAug 20, 2025
    What to do if pro.point Pressure Washer is leaking water at the pump?
    • S
      steven04Aug 20, 2025
      If your pro.point Pressure Washer is leaking water at the pump, start by tightening any loose connections. If the leak persists, it could be due to worn piston packing or broken O-rings, or the pump head or tubes may be damaged from freezing. In these cases, it's best to have the parts cleaned or replaced by an authorized dealer.
  • E
    Elizabeth OrtizAug 26, 2025
    Why does my pro.point Pressure Washer have low pressure after normal use?
    • S
      Scott PughAug 26, 2025
      If your pro.point Pressure Washer experiences low pressure after a period of normal use, it could be due to worn seals or packing, obstructed valves, a worn unloader piston, or a worn E-Z start valve. It is recommended to have these parts cleaned or replaced by an authorized dealer.
  • M
    Maria WattsAug 30, 2025
    How to stop water leaking from the spray gun connection on my pro.point Pressure Washer?
    • L
      Lisa TurnerAug 30, 2025
      If your pro.point Pressure Washer is leaking water at the spray gun/spray wand connection, first check the O-ring for wear or breakage and replace it if necessary. Also, ensure the hose connection is tight.
  • K
    Kevin JohnsonSep 4, 2025
    Why is the detergent not mixing in my pro.point Pressure Washer?
    • L
      Lori CaldwellSep 4, 2025
      If the detergent is not mixing in your pro.point Pressure Washer, make sure the siphon hose end is fully submerged in the detergent. Also, ensure you are using the Black Soap Nozzle, which allows for proper mixing of water and detergent.

pro.point 8913204 Specifications

General IconGeneral
Brandpro.point
Model8913204
CategoryPressure Washer
LanguageEnglish