Procom FBD28T - User Manual

Other manuals for Procom FBD28T

Manual27 pages

Questions and Answers

P
Phillip LopezSep 23, 2025
Why is there a high yellow flame during burner combustion in my Procom FBD28T?
- T
  Tiffany GuzmanSep 23, 2025
  If you notice a high yellow flame during burner combustion in your Procom Indoor Fireplace, it could be due to insufficient air supply. Check the burner for dirt and debris, and clean it if necessary. Alternatively, the gas regulator may be defective, requiring replacement. Also, the inlet gas pressure could be too low, so you should contact your local gas supplier.
D
Devon HarveyAug 25, 2025
Why do I smell gas when Procom FBD28T Indoor Fireplace is off?
- S
  Sara ScottAug 25, 2025
  If you smell gas even when your Procom Indoor Fireplace control knob is in the OFF position, it indicates a gas leak. You should locate and correct all leaks.
C
Charles BrownAug 25, 2025
What to do if my Procom Indoor Fireplace shuts off while in use?
- N
  Natalie GreenAug 26, 2025
  If your Procom Indoor Fireplace heater shuts off during use, with the ODS operating, try opening a window or door for ventilation. If that doesn't work, contact your local gas supplier or clean the ODS/pilot.
M
matthewstephensAug 26, 2025
Why is the flame high and yellow on my Procom FBD28T?
- F
  fmccormickAug 27, 2025
  If you see a high yellow flame during burner combustion in your Procom Indoor Fireplace, check the burner for dirt and debris and clean it if necessary. If the problem persists, replace the gas regulator or contact your gas supplier.
C
Carmen FosterSep 23, 2025
Why is there slight smoke or odor during initial operation of my Procom FBD28T?
- A
  Anthony ShieldsSep 23, 2025
  The slight smoke or odor during the initial operation of your Procom Indoor Fireplace is likely due to residues from the manufacturing process. This issue should resolve itself after a few hours of operation.
K
kirbydawnSep 13, 2025
Why is there a gas odor during combustion in my Procom FBD28T?
- C
  catherine47Sep 13, 2025
  If you notice a gas odor during combustion in your Procom Indoor Fireplace, there might be foreign matter between the control valve and burner; disassemble the gas tubing to remove any obstructions. Additionally, there could be a gas leak. You should locate and correct all leaks.
M
Marissa KruegerSep 12, 2025
What to do if burner(s) does not light after ODS/pilot is lit in Procom FBD28T?
- N
  Nichole WrightSep 12, 2025
  If your Procom Indoor Fireplace burner(s) does not light after the ODS/pilot is lit, it could be due to a clogged burner orifice. Try cleaning the burner orifice or replacing it. Also, the burner orifice diameter might be too small, in which case you should replace it. Finally, the inlet gas pressure could be too low, so you should contact your local gas supplier.
K
kingerinSep 12, 2025
Why does the flame go out when I release the control knob on my Procom Indoor Fireplace?
- J
  jason07Sep 12, 2025
  If the ODS/pilot lights but the flame goes out when you release the control knob on your Procom Indoor Fireplace, ensure the control knob is fully pressed in and held for at least 30 seconds after the pilot lights. Also, make sure the equipment shutoff valve is fully open. Check the thermocouple connection at the control valve and hand tighten it until snug, then tighten it an additional 1/4 turn. If the pilot flame isn't touching the thermocouple, contact your local gas company, or clean/replace the ODS/pilot assembly. If the thermocouple is damaged, replace it.
P
Pedro WilliamsSep 4, 2025
Why is there condensation on my windows when using Procom FBD28T?
- T
  Timothy HansonSep 4, 2025
  If you notice moisture or condensation on the windows when using your Procom Indoor Fireplace, refer to the air for combustion and ventilation requirements.
W
wesley72Sep 2, 2025
Why is my Procom FBD28T Indoor Fireplace making a whistling noise?
- C
  Courtney WilkinsonSep 2, 2025
  If your Procom Indoor Fireplace produces a whistling noise when the burner is lit, turn the control knob to the low position and let it warm up for a minute. Operate the burner until air is removed from the line, and have the gas line checked by your local propane/LP gas company. Ensure you observe minimum installation clearances and clean the burner.