Why does my Procom FBD32RT produce unwanted odors?
If your Procom Indoor Fireplace produces unwanted odors, ventilate the room and stop using odor-causing products while the heater is running. If you have a gas leak, locate and correct all leaks. For propane/LP models, refill the supply tank.
What to do if burner(s) does not light after ODS/pilot is lit on my Procom Indoor Fireplace?
If your Procom Indoor Fireplace burner(s) does not light after the ODS/pilot is lit, the burner orifice may be clogged. Clean the burner orifice or replace it. The burner orifice diameter might be too small, so replace the burner orifice. Also, the inlet gas pressure could be too low. In this case, contact your local gas supplier.
What to do if ODS/pilot lights but flame goes out when control knob is released on Procom FBD32RT?
If the ODS/pilot lights but the flame goes out when the control knob is released on your Procom Indoor Fireplace, ensure the control knob is fully pressed in and hold it for 30 seconds after the pilot lights. Also, make sure the equipment shutoff valve is fully open. Check that the thermocouple connection is snug at the control valve, tightening it by hand until it's snug, then give it an additional 1/4 turn. Low gas pressure can cause this issue, so contact your local natural or propane/LP gas company. A dirty or partially clogged ODS/pilot can also be the cause, so clean or replace the ODS/pilot assembly. If the thermocouple is damaged, replace it. If the control valve is damaged, contact customer service.
Why is there a gas odor even when control knob is in OFF position in Procom FBD32RT Indoor Fireplace?
If you smell gas when the control knob is in the OFF position on your Procom Indoor Fireplace, there may be a gas leak. Locate and correct all leaks. If there is no leak, the control valve may be defective. In this case, contact customer service.
How to fix no spark at ODS/pilot when ignitor button is pressed in Procom FBD32RT Indoor Fireplace?
If the ignitor button is pressed and there is no spark at the ODS/pilot of your Procom Indoor Fireplace, the ignitor electrode may be positioned wrong or broken, so replace the electrode. The ignitor electrode may not be connected to the ignitor cable, so replace the ignitor cable. The ignitor cable could be pinched or wet, so free the ignitor cable if pinched and keep it dry. A broken ignitor cable can cause this, so replace the ignitor cable. The piezo ignitor might be bad, so replace it. Also, check for a low battery and replace it if necessary.
Why does my Procom FBD32RT shut off while in use?
If your Procom Indoor Fireplace shuts off in use (ODS operates), there may not be enough fresh air available, so open a window or door for ventilation. Low line pressure can also cause this, so contact your local gas supplier. The ODS/pilot may be partially clogged, so clean the ODS/pilot.
Why is there condensation on windows when using Procom FBD32RT?
If you notice moisture or condensation on the windows when using your Procom Indoor Fireplace, it is likely due to not enough combustion/ventilation air.
Why is the flame high and yellow during burner combustion in my Procom FBD32RT Indoor Fireplace?
If your Procom Indoor Fireplace has a high yellow flame during burner combustion, check the burner for dirt and debris and clean it if found. The gas regulator may be defective, so replace it. The inlet gas pressure may be too low, so contact your local gas supplier.
What causes burner backfiring during combustion in Procom FBD32RT Indoor Fireplace?
If your Procom Indoor Fireplace burner backfires during combustion, the burner orifice may be clogged or damaged, so clean or replace the burner orifice. The burner may be damaged, so contact your dealer or customer service. The gas regulator may be damaged, so replace the gas regulator.
What causes delayed ignition of burner(s) in Procom FBD32RT?
If your Procom Indoor Fireplace has delayed ignition of burner(s), the manifold pressure may be too low, so contact your local gas supplier. The burner orifice may be clogged, so clean the burner or replace the burner orifice.
Discusses the need for adequate ventilation and defines classifications for air supply.
Provides a worksheet to calculate required fresh air based on space volume and appliance BTU input.
Specifies required clearances from combustible materials for safe installation.
Details the process for changing the gas type from propane/LP to natural gas and vice versa.
Details safety precautions and requirements for connecting the heater to the gas supply.
Provides procedures for testing gas supply piping and heater connections for leaks.
Crucial safety warnings and instructions to follow before attempting to light the appliance.
Step-by-step guide on how to safely light the pilot and main burner.
Lists common ignitor issues, possible causes, and corrective actions.
Addresses problems with pilot flame not appearing or going out after release.
Covers issues like burner not lighting, delayed ignition, backfiring, and high yellow flame.
General| Brand | Procom |
|---|---|
| Model | FBD32RT |
| Category | Indoor Fireplace |
| Language | English |
To Next Page
