Procopi ESS - User Manual

1/84
2015/02 - Indice de révision : B - Code : 29650
ELECTROLYSEUR ESS ET ESS PRO
CHLORINATOR
NOTICE D’INSTALLATION ET CONSEILS D’UTILISATION
(à lire attentivement et à conserver pour utilisation ultérieure)
p.1
GB
DE
FR
p.29
S.57

Summary

Product Description and Operating Instructions

Safety Recommendations

User Safety

Guidance on safe installation and use of the electrical/ control panel and its components.

Safety of Materials and Premises

Recommendations for protecting the equipment and surrounding areas from hazards.

Locking; Unlocking the Key Pad

Instructions on how to secure and access the device's control panel.

Installation

Hydraulic Connections

Details on connecting the device's components within the pool's hydraulic system.

Sample Configurations

Illustrations of typical installation layouts for the electrolyser system.

Location of EES Pro pH and Redox Probes

Guidance on optimal placement of pH and Redox probes for accurate readings.

Precautions Concerning the Probes

Important guidelines for handling and maintaining the pH and Redox probes.

Installation of the pH-Clear Pump

Instructions for installing the optional pH-Clear pump, including tubing connections.

When Starting Up for the First Time

Steps for initial setup and priming of the pH-Clear pump.

Installing the Probes

Procedure for mounting the pH and Redox probes onto the fitting.

Redox Probe

Specific instructions for installing the Redox probe, including sealing.

pH Probe

Detailed steps for installing the pH probe, including connections and sealing.

Installing the Electrical; Control Panel

Guidelines for mounting the main control panel securely on a wall.

Connection of the Various Components to the Electrical Panel

Diagram and instructions for wiring all system components to the main control panel.

Wiring in the Control Panel

Detailed electrical wiring diagram and power supply recommendations for the control panel.

Adding Salt to the Pool

Chlorine Stabilisation

Starting the Electrolyser

Parameter Settings and Functions

Chlorine Output

How to adjust and set the chlorine production level for EES models.

Viewing the Measured pH and Redox Values (EES Pro Only)

Instructions for checking pH and Redox readings on the EES Pro model.

Setting the pH and Redox Set Point (EES Pro Only)

Guide to configuring the desired pH and Redox set points for the EES Pro.

Turbo Mode

How to activate and set the duration for the Turbo mode for increased chlorine production.

Cover Mode

Explanation of the Cover Mode function for reduced chlorine production when the pool cover is on.

Punctual or Periodic Reduction of the pH by the pH-Clear Pump

Setting the pH-Clear pump for timed or single acid injections to lower pH.

Cell Cleaning - Auto mode

Programming automatic acid injection frequency for cell descaling.

Cell Cleaning-Manual mode

Performing manual, immediate acid injection for cell descaling.

Warning and Error Messages

Salt Concentration Too Low or Too High

Interpreting and resolving warnings related to incorrect salt levels in the pool.

Electrical Problems with the Cell

Troubleshooting messages indicating electrical faults within the cell or its circuit.

Flow Rate Too Low

Diagnosing and fixing issues when the water flow rate is insufficient for operation.

Water Temperature Is Too Low

Understanding the impact of low water temperature on chlorine output.

Temperature in the Electrical Panel Is Too High

Addressing overheating issues within the electrical panel.

Replacing the pH-Clear Pump Compression Tube (EES Pro Only)

Procedure for replacing the peristaltic pump's compression tube.

Pump Disconnected (EES Pro Only)

Troubleshooting the 'NEED PUMP' message when the pump is disconnected.

High and Low pH and Redox Alarms (EES Pro Only)

Resolving alarms related to high or low pH and Redox values.

pH or Redox Probe Faults (EES Pro Only)

Troubleshooting messages indicating faults with the pH or Redox probes.

pH;Redox Circuit Board Fault (EES Pro Only)

Resolving issues indicated by a 'NO CARD' probe connection board fault.

Maintenance

Maintenance of pH and Redox Probes (EES Pro Only)

Cleaning and inspecting the pH and Redox probes to ensure proper function.

Calibrating the pH Probe (EES Pro Only)

Step-by-step guide for calibrating the pH probe using buffer solutions.

Calibrating the Redox Probe (EES Pro Only)

Procedure for calibrating the Redox probe using a buffer solution.

Replacing the Compression Tube on the Peristaltic Pump

Detailed instructions for replacing the peristaltic pump's compression tube.

Manual Dismantling and Descaling of the Cell

Winterizing

A) Passive Winterizing

Procedure for protecting the system components during winter shutdown.

pH-Clear Pump

Specific winterizing steps for the pH-Clear pump and its tubing.

Cell

Instructions for winterizing the electrolysis cell, including descaling.

Probes

Steps for winterizing the pH and Redox probes, including storage.

B) Active Winterizing

Guidelines for active winterization, including daily filtration requirements.

XI. Appendix 1 - Troubleshooting

Concentration of free Chlorine in the pool is too low

Troubleshooting steps for low free chlorine levels, including device, probe, and water parameter checks.

Water is turning green, or brown stains are appearing on the pool walls and floor.

Diagnosing and correcting water discolouration issues related to chlorine or metal content.

The device remains off, even though it should be working

Troubleshooting why the device is not operating when expected.

The Chlorine output cannot reach 100%

Identifying reasons why the electrolyser is not achieving maximum chlorine output.

Procopi ESS Specifications

General

Brand	Procopi
Model	ESS
Category	Swimming Pool Cleaners
Language	English