How to fix weak stimulation or no stimulation from ProMed Medical Equipment?
If the stimulation from your ProMed Medical Equipment is weak, or you cannot feel any stimulation, try replacing and reconnecting the electrodes. If that doesn't work, replace the lead wires. Also, make sure that the intensity level is not too weak, and increase it if necessary.
How to fix ineffective stimulation with ProMed EMT-6?
If the stimulation is ineffective when using ProMed Medical Equipment, it may be due to improper electrode and applicator placement. Reposition the electrode and applicator.
What to do if the skin becomes red or I feel a stabbing pain using ProMed EMT-6?
If you experience a red skin or a stabbing pain while using ProMed Medical Equipment, it could be due to several reasons. You might be using the electrodes on the same site repeatedly, in which case you should reposition them. If you feel pain or discomfort, stop use immediately. The electrodes may not be sticking properly, so ensure they are securely attached to the skin. Dirty electrodes can also cause this, so clean them with a damp, lint-free cloth or replace them. Finally, a scratched electrode surface can be the culprit, requiring a replacement of the electrode.
Why is the stimulation uncomfortable when using ProMed Medical Equipment?
If the stimulation from your ProMed Medical Equipment feels uncomfortable, it could be due to several factors. The intensity might be too high, so try decreasing it. The electrodes may be too close together; reposition them. Damaged or worn electrodes or lead wires can also cause discomfort, so replace them if necessary. Ensure the electrode active area is not too small; replace them with ones that have an active area no less than 16.0 cm2 (4cm*4cm). Review the manual to ensure proper operation. Verify the connection is secure and firm. Also, try turning down the intensity and rotating the lead wires in the socket by 90 degrees; if the issue continues, replace the lead wire. If problems persist after these steps, a component may have failed.
What to do if the output current stops during ProMed EMT-6 therapy?
If the output current stops during therapy with your ProMed Medical Equipment, it could be due to a few reasons. The electrode pads might have come off the skin; turn off the device and firmly reattach the pads. The cable might be disconnected; turn off the device and reconnect it. Alternatively, the batteries might be exhausted; replace them with new ones.
Why do the displays fail to light up on my ProMed Medical Equipment?
If the displays on your ProMed Medical Equipment fail to light up, it could be due to battery contact failure. Try using fresh batteries. Also, ensure the batteries are inserted correctly and check that all contacts are in place and not broken.
What to do if ProMed EMT-6 causes skin redness or stabbing pain?
If you experience skin redness or stabbing pain while using the ProMed Medical Equipment, take these steps: * Re-position the electrodes. * Make sure the electrodes stick securely to your skin. * Clean the electrode pads with a damp, lint-free cloth or replace them. * Replace the electrode if its surface is scratched. If you continue to feel pain or discomfort, stop use immediately. This may occur if you use the electrodes on the same site every time, the electrodes aren’t stuck onto the skin properly, the electrodes are dirty, or the surface of the electrode was scratched.
Why is stimulation from ProMed Medical Equipment uncomfortable?
Uncomfortable stimulation from your ProMed Medical Equipment can occur due to several reasons. The intensity may be too high, so try decreasing it. The electrodes might be too close together; reposition them. Damaged or worn electrodes or lead wires can also cause discomfort, so replace them. Ensure the electrode active area size is adequate, no less than 16.0 cm2(4cm*4cm), replace if needed. Finally, ensure you are operating the device according to the manual.
How to fix weak stimulation with ProMed EMT-6 Medical Equipment?
If the stimulation from your ProMed Medical Equipment feels weak or you cannot feel any stimulation, this could be due to several factors. The electrodes may be dried out, contaminated or not properly placed, in that case replace and reconnect them. Old, worn, or damaged lead wires can also cause this issue, so replace them. Also, make sure that the intensity level isn't too weak, use a higher intensity level if needed.
What to do if output current stops during ProMed EMT-6 therapy?
If the output current stops during therapy with your ProMed Medical Equipment, it could be due to a few reasons. The electrode pads may have come off the skin, so turn off the device and stick the electrode pad firmly to the skin. The cable might be disconnected, so turn off the device and connect the cable. The batteries may be exhausted, so replace them with new batteries.
Overview of the device components and their functions.
Explanation of the symbols and information displayed on the device screen.
Lists conditions where the device should not be used or used with caution.
Key safety warnings for device operation and user care.
Details on user precautions and potential adverse effects.
Guidance on applying electrode pads to the skin correctly.
Steps for connecting device components for operation.
General| Type | Emergency Transport Ventilator |
|---|---|
| PEEP Range | 0 - 20 cmH2O |
| Oxygen Concentration | 21 - 100% |
| Battery Life | Up to 6 hours |
| Modes | A/C, SIMV, CPAP |
| Power Source | AC Power, Internal Battery |
| Weight | 4.5 kg |
To Next Page
