019
General Settings
Press button to turn the thermostat on/off. When thermostat is turned off, the LCD will only display current temperature reading.
To Access the Settings: With the thermostat in the off position. (It will only display the mode and temperature when turned off). Press and hold the
M
button for 3-5 seconds to bring
up a configuration menu. In this mode you simply press the
M
button to select the different menu numbers. Once you have selected the Menu number you want to change simply use the
arrow keys to adjust the settings.
Menu # Features description Features Explanation Adjustment (press up or down button to adjust)
01 Model (Model Selection) The Thermostat can operate in several modes allowing you to choose between three
different variations. ‘A’, ‘AF’ and ‘F’ mode. ‘A’ mode: Air temperature only using the built
in sensor, ‘AF’ mode: Air and floor temperature using built in sensor and remote floor
probe, ‘F’ mode: floor temperature using the floor probe.
A – Air Temperature
AF – Air and Floor Temperature
F – Floor Temperature
02 S.D (switching differential) The number of degrees the temperature has to change before the unit switches on/off.
The default is 1 degree so if the temperature is set to 21 degrees the thermostat will
switch on at 20.5 degrees and off at 21.5 degrees. 0.5 degrees either side of 21.
1 = 1 degree(default), 2 =2 degrees
03 ATC (air temp calibrate) This to calibrate the Air temperature sensor. -1 = decrease 1 degree, 1 = increase 1 degree
04
FTC (Floor temp calibrate) This to calibrate the Floor temperature sensor. -1 = decrease 1 degree, 1 = increase 1 degree
05 PTD (program time delay)
This is the time the unit allows the user to have a pause/break whilst programming before the
thermostat returns to the home screen.
5s, 10s, 15s, 20s (default), 25s, 30s.
06 TR-AF (AF model only)
(TR=Temperature readout)
In AF mode the user has the option to see the floor temperature, air temperature or the
unit can switch display between both floor and air temperature at 5 second intervals.
A=to show air temperature, F=to show floor
temperature, A-F = to show both in 5 second intervals
07 MAXFT (set maximum
floor temp in AF model)
In AF mode a maximum floor temperature can be programmed so the floor does not
exceed this.
20-40 degree (default 28ºC)
08 BL (back light turning-on
time setting)
The time that the back light stays illuminated after a button is pressed. Can also be
permanently on or off.
10s, 20s, 30s, 40s 50s, 60s, ON or OFF
09 TF (temperature format) The way temperature format is displayed on the screen. Degrees Celsius. Degrees Fahrenheit
10 Clock 12 or 24 hours clock format. 12H or 24H
11 FP (Frost protection) Frost protection allows the thermostat to turn on if the temperature drops below 5
degrees even when it is not programmed to.
on= activated, off= deactivated
12 SC (setpoint configuration) This allows the user to set between two different programming options. 2 = (default)
This means throughout one day you can have four
programmes but with only two different temperatures. i.e.
programme 1 and 3 will have the same temperature as will
programme 2 and 4.
4 = You can have four different temperatures, an independent
one for each of the 4 programmes.
Please Note: one of the following error messages will appear if one of these problems occur:
LO - This error means that the room or floor temperature is below 0°C
HI - This error means that the room or floor temperature is greater than 50°C
If the floor sensor is short-circuit or broken, the LCD will display “ERR” and the thermostat will cut off output.
This product should be installed by a qualified electrician.
To Previous Page
Loading...
