08
Copyright © 2023 Shenzhen Pudu Technology Co., Ltd. All rights reserved.
No organization or individual shall imitate, copy, transcribe or translate the contents of this user
manual, in part or in full,without the express written consent of Shenzhen Pudu Technology Co., Ltd.,
or distribute this user manual for prot in anyway (electronically or via photocopying, recording, etc.).
The product specications and information provided in this user manual are for reference only and are
subject to change without further notice. Unless otherwise specied, this user manual is only intended
as a user guide, and no representation shall be deemed as a warranty of any kind.
1.1 Instructions for use
・workstation users should receive professional training from technical support personnel.
・Deployment of workstations may involve lightweight construction of waterways or circuits, so
professionals are required to implement
・The workstation should be placed in an indoor scene with normal temperature. It is forbidden to
place the workstation in a high temperature area (> 40° C) for use
・If the workstation is damaged, the charging current is abnormal, or the charging/draining is
abnormal, please stop using the workstation.
・Be sure to use the original power cord, and it is strictly forbidden to use non-original power cords to
supply power to the workstation.
・Carefully protect the power cord to avoid pulling and twisting.
・It is strictly forbidden for the workstation to collide with foreign objects, causing damage to the
workstation.
・Do not use the workstation near ammable and explosive objects.
・If the workstation emits smoke or burnt smell, it means that the workstation is abnormal. Please
disconnect the power supply of the workstation immediately and contact Purdue sta.
・Do not move the workstation arbitrarily when in use, and use the workstation at the designated
location.
・This workstation can only be used with CC1, and it is strictly forbidden to use this workstation for
products produced by other companies.
・It is strictly forbidden to store or work in areas exposed to direct sunlight.
・If there is an abnormal red light on the workstation, please separate the robot from the workstation.
Wait for the workstation light to turn green before it can be used again;
・If the red light does not go o for a long time, please contact technical support personnel.
・If you need to use the function of automatically adding cleaning solution, please use non-foaming
cleaning agent. Prohibit the use of strong corrosive cleaning agents such as strong acid and strong
alkali
・Be sure to tighten the water pipe joint.
・This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
・Children should be supervised to ensure that they do not play with the appliance.
・Warning against recharging non-rechargeable batteries
・SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for
battery charger Models SDBC01.
・Before using battery charger, read all instructions and cautionary markings on battery charger,
battery, and product using battery
・CAUTION - To reduce risk of injury, charge only Li-ion type rechargeable batteries ((DC 25.6V,
Max.50Ah). Other types of batteries may burst causing personal injury and damage.
Safety Instructions
07
1.2 Environmental Notice
・Working environment temperature: 0° C ~40° C, relative humidity: ≤ 90% (<40° C).
・Storage ambient temperature: -20° C ~70° C, relative humidity ≤ 85%, storage for 1 year.
・ Working environment requirements:
1. The workstation needs to be placed on a at ground for use, with its back against a at wall, and
xed to the wall or the ground through lateral connection components.
2. There are no reective or light-transmitting parts such as mirrors or glass in the working position
of the workstation. If it is unavoidable, the environment may need to be modied to a certain extent.
3. There should be no ammable objects around the charging pile.
4. During normal operation, keep open and unobstructed within 2 meters in front and 1.5 meters in
the left and right directions.
2m
1.5m
To Next Page
Loading...