Why is my Pure Enrichment MISTAIRE not producing mist?
If your Pure Enrichment Humidifier is blowing air but not producing mist, it could be due to excessive water. Pour out the extra water. Another reason might be residue inside the tank, so wash the tank and try again. Also, the ultrasonic disk might be dirty. In that case, clean the disk. Finally, if you are using hard water, replace it with softer water.
What to do if my Pure Enrichment MISTAIRE humidity level is low?
If the humidity level is low when using your Pure Enrichment Humidifier, the ultrasonic disk might be dirty; in that case, clean the disk. Also, if the water in the unit is too cold, replace it with cool water.
Why is water accumulating around my Pure Enrichment Humidifier?
If water is accumulating outside of your Pure Enrichment Humidifier, it could be due to saturation of humidity. Lower the mist control setting. Alternatively, the unit might not be level. Unplug it and place it on a level surface. Also, point the mist away from objects and raise the unit on a water-resistant level surface 2-3 feet off the floor.
How to fix bad smell from Pure Enrichment MISTAIRE?
If your Pure Enrichment Humidifier has a bad smell, it is likely due to poor maintenance or dirty water. Clean the humidifier thoroughly and fill it with fresh water.
How to prevent white dust from Pure Enrichment MISTAIRE Humidifier?
If white dust is forming on nearby furniture when using your Pure Enrichment Humidifier, it may be due to hard water depositing dust. If it persists, use distilled water.
Why is water dripping when refilling my Pure Enrichment MISTAIRE?
If water is dripping when refilling your Pure Enrichment Humidifier, it is likely due to water remaining on the bottom of the tank. Wipe the tank or tilt it to drain before transporting.
Essential safety instructions for operating the humidifier, including handling, placement, and intended use to prevent injury.
Prohibits use with damaged plugs, wet hands, or specific environments like near sinks or heat sources.
Details device compliance with FCC rules and provides measures to correct radio frequency interference.
Lists key product details including size, power, coverage area, run time, tank capacity, and moisture output.
Guidance on selecting a location, placing the unit, and the steps for filling the water tank correctly.
Explains the 2-speed mist control, low water level indicator, mist director, and night light functionality.
Details the included cleaning brush and automatic shut-off feature when the tank is removed.
Instructions for cleaning the inside base, water tank, and outer surface of the humidifier.
Guidance on removing scale, using distilled water, and cleaning the ultrasonic disk with the provided brush.
Addresses problems like no mist, low humidity, bad smells, white dust, and unit stopping with corresponding fixes.
Solutions for water accumulation, dripping, noise, and the red LED light indicating low water.
Details the 5-year warranty, what it covers, and exclusions for damage from improper use.
Instructions for registering the product online for full warranty benefits and customer support.
The MistAire Ultrasonic Cool Mist Humidifier, model PEHUMIDIF, is a tabletop device designed to add moisture to the air in your home or office, helping to alleviate dry air conditions. It operates using ultrasonic technology to produce a cool mist.
The primary function of the MistAire humidifier is to generate a cool mist to increase the humidity level in a room. This is achieved through an ultrasonic disk that vibrates at a high frequency, converting water into a fine mist that is then dispersed into the air. The device is equipped with a 2-speed mist control, allowing users to select between a low or high moisture output to suit their preferences and the room's needs. An integrated night light feature provides ambient illumination, which can be turned on or off independently of the mist output. The mist director, located at the top of the unit, can be rotated 360 degrees, enabling users to direct the mist flow in any desired direction. For safety, the humidifier includes a low water level indicator that changes from green to red and automatically shuts off the unit when the water tank is nearly empty, preventing damage to the device. Additionally, the power automatically shuts off if the water tank is removed from the base during operation.
Setting up the MistAire humidifier involves selecting a firm, level, and flat surface, ensuring it is at least six inches away from walls or objects for proper airflow. It should be placed on a water-resistant surface to prevent potential water damage to furniture or flooring. The humidifier is filled by separating the water tank from the base, flipping the tank over, and opening the tank lid by turning it to the left. Cool, clean water is then poured directly into the tank; hot or boiling water should not be used. After filling, the tank lid must be firmly secured by turning it to the right, and the tank reattached to the base. The device is operated via a single power button, which cycles through different modes: Mode 1 (Low Speed, Night Light OFF), Mode 2 (Low Speed, Night Light ON), Mode 3 (High Speed, Night Light ON), Mode 4 (High Speed, Night Light OFF), and Off Mode (Night Light OFF). This intuitive control allows for easy adjustment of both mist intensity and night light function. Users are advised not to place the product on cloth, carpet, or other absorbent surfaces, as this may block the air inlet. It is also important to avoid placing the mist spout directly at objects or people. The device is designed for use with clean or distilled water; hard water areas may necessitate more frequent cleaning.
Regular cleaning is crucial for maintaining the performance and longevity of the MistAire humidifier. Before any servicing, the unit must always be unplugged. General cleaning involves pouring out excess water from the base and washing it with fresh water, using the included cleaning brush and a soft cloth. The base should not be submerged in water, and water should not enter the dry air exhaust port. The water tank should be emptied, and the mist nozzle and mist tube cleaned with fresh water and a bottle cleaning brush (not included). The outer surface of the unit can be wiped with a soft, damp cloth. If water accumulates on the surface during use, reducing humidity and drying the exterior with a cloth is recommended.
Descaling is an important maintenance task, especially in hard water areas, and may be required weekly or every other week. To descale, unplug the humidifier, remove the tank, and empty all water from the base and tank. The ultrasonic disk, located in the center of the base unit, should be gently cleaned using ONLY the enclosed cleaning brush to remove buildup and deposits. It is crucial not to scrub or scrape the ultrasonic disk with anything other than the provided brush. If scale becomes difficult to remove, a mixture of 1 tsp. white vinegar and 1 tsp. water can be poured into the base and allowed to stand for 5 minutes. After this, all interior surfaces should be cleaned with a soft cloth or brush, and the base thoroughly rinsed with water to remove scale and vinegar solution. The mist nozzle and mist tube in the water tank should also be checked and cleaned as needed. To prevent mineral deposits or "white dust" in hard water areas, the use of distilled water is recommended, or a decalcification cartridge or humidifier cleaner capsule can be used. Harsh detergents or cleaning chemicals should not be used on the unit or water tank. For end-of-season storage, the humidifier should be completely dry before being packed in its original carton and stored in a cool, dry location; water should never be left in the base or tank during storage. Users are cautioned not to attempt to open the motor housing themselves, as this will void the warranty and could cause damage or personal injury.
General| Water Tank Capacity | 1.5 Liters |
|---|---|
| Automatic Shut-Off | Yes |
| Coverage Area | Up to 250 sq ft |
| Noise Level | ≤30dB |
| Mist Output | 150ml/h |
| Night Light | Optional |
| Power Source | AC power (120V) |
| Settings | 2 mist settings (high/low) |
To Next Page
