Need help?Do you have a question about the Pyle Pro PT110 and is the answer not in the manual?
Power| output power at THD 10%, 1 kHz | 20W |
|---|---|
| maximum power | 80W |
| power requirement | 120V AC, 60 Hz/240V AC, 50 Hz |
| power fuse 120V AC | 1.2A |
| power fuse 240V AC | 0.6A |
Audio| THD at 1W, 1 kHz Low-Pass Filter MIC 1 | 1% |
|---|---|
| THD at 1W, 1 kHz Low-Pass Filter MIC 2 | 1% |
| THD at 1W, 1 kHz Low-Pass Filter AUX/CD | 0.1% |
| THD at 1W, 1 kHz Low-Pass Filter PHONO | 0.1% |
| frequency response MIC 1 | 80 Hz - 20 kHz |
| frequency response MIC 2 | 80 Hz - 20 kHz |
| frequency response AUX/CD | 80 Hz - 20 kHz |
| frequency response PHONO | +13 dB/-13.5 dB |
| input sensitivity MIC 1 | 2.5 mV |
| input sensitivity MIC 2 | 2.5 mV |
| input sensitivity AUX/CD | 150 mV |
| input sensitivity PHONO | 3.5 mV |
| signal-noise ratio MIC 1 | 60 dB |
| signal-noise ratio MIC 2 | 60 dB |
| signal-noise ratio AUX/CD | 70 dB |
| signal-noise ratio PHONO | 60 dB |
| noise level input shorted | 0.75 mV |
| tone control | -15 dB (High Cut at 10 kHz) |
Weight and Dimensions| dimensions | 3 1/3 x 12 3/4 x 8 9/10 inches, 85 x 324 x 226 mm |
|---|---|
| weight | 3.56 kgs |
Power| output power at THD 10%, 1 kHz | 40W |
|---|---|
| maximum power | 120W |
| power requirement | 120V AC, 60 Hz/240V AC, 50 Hz |
| power fuse 120V AC | 1.5A |
| power fuse 240V AC | 0.75A |
Audio| THD at 1W, 1 kHz Low-Pass Filter MIC 1 | 1% |
|---|---|
| THD at 1W, 1 kHz Low-Pass Filter MIC 2 | 1% |
| THD at 1W, 1 kHz Low-Pass Filter AUX/CD | 0.1% |
| THD at 1W, 1 kHz Low-Pass Filter PHONO | 0.1% |
| frequency response MIC 1 | 80 Hz - 20 kHz |
| frequency response MIC 2 | 80 Hz - 20 kHz |
| frequency response AUX/CD | 80 Hz - 20 kHz |
| frequency response PHONO | +13 dB/-13.5 dB |
| input sensitivity MIC 1 | 2.5 mV |
| input sensitivity MIC 2 | 2.5 mV |
| input sensitivity AUX/CD | 150 mV |
| input sensitivity PHONO | 3.5 mV |
| signal-noise ratio MIC 1 | 60 dB |
| signal-noise ratio MIC 2 | 60 dB |
| signal-noise ratio AUX/CD | 70 dB |
| signal-noise ratio PHONO | 60 dB |
| noise level input shorted | 0.75 mV |
| equalizer control range 100 Hz | +/- 10 dB |
| equalizer control range 1 kHz | +/- 10 dB |
| equalizer control range 8 kHz | +/- 10 dB |
Weight and Dimensions| dimensions | 3 1/3 x 12 3/4 x 8 9/10 inches, 85 x 324 x 226 mm |
|---|---|
| weight | 3.92 kgs |
To Next Page
