To Next Page
J
jillian26Sep 6, 2025
What should I do if the Laser Head housing is opened on Quantel Measuring Instruments?
- AAlison JohnsonSep 6, 2025
If the I/O cable is not connected after opening the Laser Head housing, ensure the I/O cable is fully seated.
What should I do if the Laser Head housing is opened on Quantel Measuring Instruments?
If the I/O cable is not connected after opening the Laser Head housing, ensure the I/O cable is fully seated.
What to do if Quantel Ultra Big Sky Laser Measuring Instruments show low coolant level?
If the Quantel Measuring Instruments system is low on coolant, ensure it is properly filled after draining. Refer to the instructions in Maintenance on page 68.
What to do if Quantel Measuring Instruments display charger/simmer over temp?
If the charger inductor is too hot, turn OFF power to the ICE450 and allow it to cool. Make sure that airflow is not obstructed at the front or back of the ICE450. If the interlock condition persists, there may be a problem with the charger circuitry. In this case, contact Quantel Customer Service.
Why is the coolant temperature high in my Quantel Measuring Instruments?
If the coolant is too warm for proper operation, turn off the ICE450 and allow it to cool. The high-temperature setting may need to be increased, or the cooling fans may have failed. Contact Quantel Customer Service for these issues.
What causes low coolant temperature in Quantel Ultra Big Sky Laser Measuring Instruments?
If the coolant is not warm enough for proper operation, allow time for the coolant to warm. The low-temperature setting may need to be reduced, or the heater minimum power setting may need adjustment. The heater circuit may have failed. Contact Quantel Customer Service for these issues.
Why is there no system power in my Quantel Ultra Big Sky Laser?
If there is no power connected, check the simple things first—make sure the power cord is plugged into the outlet and making connection to the back of the ICE.
How to resolve flashlamp disabled time out delay expired on Quantel Ultra Big Sky Laser Measuring Instruments?
If the flashlamp timeout has expired, disable timeouts or change the flashlamp timeout to 00:00.
What to do if simmer disabled time out delay expired on Quantel Measuring Instruments?
If the simmer timeout has expired, you should not attempt to repair this problem. Contact Quantel Customer Service for repair.
What to do if Quantel Ultra Big Sky Laser Measuring Instruments show defective temp. sensor error?
If one or more of the three feedback thermistor circuits (coolant, charger/ simmer, and harmonic generator) is faulty or is running too cold, ensure all temperatures are above 18 °C. If the system does not include a harmonic generator, make sure the HG option is turned off from the System Info menu.
How to fix power too high error in Quantel Ultra Big Sky Laser?
If the voltage or frequency settings are too high, resulting in power too high, reduce voltage, energy, or frequency until the power is less than 450W. Verify this and save the configuration.
General| Brand | Quantel |
|---|---|
| Model | Ultra Big Sky Laser Series |
| Category | Measuring Instruments |
| Language | English |
Defines terms and instructions for care, use, and handling of Class IV laser equipment.
Explains hazard symbols (Danger, Warning, Caution, Note) and their meanings.
Describes general hazards and unsafe practices causing damage or injury.
Lists typical hazards such as exposure, voltage, and lifting risks.
Details essential precautions for safe laser operation.
Details for connecting the ICE450, Laser Head, and Remote Box for upright and rack systems.
Procedure for filling the coolant reservoir of the standard ICE450 unit.
Procedure for filling the coolant reservoir of the rack-mounted ICE450 unit.
General safety guidelines and precautions for operating the laser system.
Specific guidelines to prevent laser damage and ensure proper operation.
Explains the function and connection of the remote interlock for safety shutdown.
Details the controls and indicators on the Remote Box unit.
Explains configuration and operation in automatic mode.
Discusses external triggering requirements and methods.
Provides a step-by-step guide to starting the laser system.
Details the steps for safely shutting down the laser system.
Explains how to decrease and increase laser output energy.
Details methods for increasing laser output energy.
Details common interlock values, messages, causes, and solutions.
General guide for identifying and resolving system issues.
