How to fix the emergency stop button pushed issue on Quantel Measuring Instruments?
If the red Emergency Stop button on the Remote Box is pushed in, pull it out. If the issue persists, it may indicate an open circuit in the Remote Box, cable, or internal harness. In this case, contact Quantel Customer Service.
How to fix power too high error in Quantel Ultra Big Sky Laser?
If the voltage or frequency settings are too high, resulting in power too high, reduce voltage, energy, or frequency until the power is less than 450W. Verify this and save the configuration.
Why am I getting a heater over temp error on my Quantel Ultra Big Sky Laser?
If the heater coolant is too hot and the protective thermal switch opened when the coolant neared 70°C, turn off power to the ICE450 and allow it to cool down. If this does not resolve the issue, the heater thermostat circuit may need repair. Contact Quantel Customer Service.
What to do if the capacitor is not discharged in Quantel Ultra Big Sky Laser Measuring Instruments?
If the flashlamp capacitor did not completely discharge after the flashlamp turned off, it indicates a fault in the charging system and may be hazardous. You should not attempt to repair this problem. Contact Quantel Customer Service for repair.
What to do if BNC Intlk is in on the ICE450 front panel of Quantel Ultra Big Sky Laser Measuring Instruments?
To resolve the “INTLK In” connector issue on the ICE450 front panel, connect the shorting plug to the “Interlock In” BNC. Verify that the shorting plug is connecting properly. If the shorting plug is OK, the issue may be an internal connection. Contact Quantel Customer Service.
How to troubleshoot low coolant flow in Quantel Measuring Instruments?
If the coolant line is obstructed preventing proper flow or the flow sensor is damaged or stuck, examine the coolant lines to ensure they are not kinked or obstructed. Make sure the pump is toggled ON from the Remote Box. The pump or the flow sensor may require repair. Notify Quantel Customer Service.
What causes low coolant temperature in Quantel Ultra Big Sky Laser Measuring Instruments?
If the coolant is not warm enough for proper operation, allow time for the coolant to warm. The low-temperature setting may need to be reduced, or the heater minimum power setting may need adjustment. The heater circuit may have failed. Contact Quantel Customer Service for these issues.
Why is the coolant temperature high in my Quantel Measuring Instruments?
If the coolant is too warm for proper operation, turn off the ICE450 and allow it to cool. The high-temperature setting may need to be increased, or the cooling fans may have failed. Contact Quantel Customer Service for these issues.
What to do if Quantel Measuring Instruments display charger/simmer over temp?
If the charger inductor is too hot, turn OFF power to the ICE450 and allow it to cool. Make sure that airflow is not obstructed at the front or back of the ICE450. If the interlock condition persists, there may be a problem with the charger circuitry. In this case, contact Quantel Customer Service.
What to do if Quantel Ultra Big Sky Laser Measuring Instruments show low coolant level?
If the Quantel Measuring Instruments system is low on coolant, ensure it is properly filled after draining. Refer to the instructions in Maintenance on page 68.
General| Brand | Quantel |
|---|---|
| Model | Ultra Big Sky Laser Series |
| Category | Measuring Instruments |
| Language | English |
Defines terms and instructions for care, use, and handling of Class IV laser equipment.
Explains hazard symbols (Danger, Warning, Caution, Note) and their meanings.
Describes general hazards and unsafe practices causing damage or injury.
Lists typical hazards such as exposure, voltage, and lifting risks.
Details essential precautions for safe laser operation.
Details for connecting the ICE450, Laser Head, and Remote Box for upright and rack systems.
Procedure for filling the coolant reservoir of the standard ICE450 unit.
Procedure for filling the coolant reservoir of the rack-mounted ICE450 unit.
General safety guidelines and precautions for operating the laser system.
Specific guidelines to prevent laser damage and ensure proper operation.
Explains the function and connection of the remote interlock for safety shutdown.
Details the controls and indicators on the Remote Box unit.
Explains configuration and operation in automatic mode.
Discusses external triggering requirements and methods.
Provides a step-by-step guide to starting the laser system.
Details the steps for safely shutting down the laser system.
Explains how to decrease and increase laser output energy.
Details methods for increasing laser output energy.
Details common interlock values, messages, causes, and solutions.
General guide for identifying and resolving system issues.
To Next Page
