What to do if Quietside QS12-VP115 doesn't turn on?
If your Quietside air conditioner isn't responding after being powered on, ensure the power plug is securely connected. If the connection is firm and it still doesn't respond, replace the controller fuse. If the issue persists, the transformer may be faulty and require replacement.
Why is my Quietside QS12-VP115 remote not working?
If your Quietside air conditioner remote controller isn't sending signals, first check the remote controller itself for any issues. Also, check the receiver connection and its wiring. If the receiver's installation and wiring are correct, replace either the receiver or the remote controller.
How to fix Quietside QS12-VP115 breaker that trips immediately?
If your Quietside Air Conditioner breaker trips immediately when turned on, first check the power supply circuit. If the circuit or a part of the air conditioner is malfunctioning, measure the insulation resistance or identify and fix the specific issue. If the breaker itself is faulty, replace it.
Why does my Quietside QS12-VP115 breaker trip after a few minutes?
If your Quietside Air Conditioner breaker trips after a few minutes, it indicates a malfunction in the circuit or a component of the air conditioner. To resolve this, measure the insulation resistance or systematically troubleshoot to identify and fix the faulty part. If the breaker itself is defective, replace it.
How to stop Quietside QS12-VP115 from leaking water?
If you notice water leakage from your Quietside Air Conditioner, inspect the drainage pipe for blockages or damage; replace the pipe if necessary. Also, check the refrigerant pipe joint's wrapping and re-wrap it tightly if it's loose.
Why is my Quietside QS12-VP115 making abnormal sounds?
If your Quietside air conditioner is making abnormal sounds, check if the indoor unit's fan is contacting other parts and adjust its location if needed. Also, check for any touching pipelines on the outdoor unit and separate them. Inspect the inner plates and tighten any loose screws, or stick absorbing clay between the plates. Finally, check the louver of the outdoor unit and adjust its position if it's touching the outer case.
What to do if Quietside QS12-VP115 power voltage is too low?
If the voltage is too low, check the cause and improve the power supply condition. Consider adding a stabilized voltage power supply if the voltage is lower than 10% of the rated voltage.
What to do if Quietside QS12-VP115 compressor runs but the outdoor fan doesn't?
If, in cooling or heating mode, the compressor of your Quietside Air Conditioner runs but the outdoor fan does not, check the wiring connections against the circuit drawing and correct any errors. If the connections are correct, the outdoor fan capacitor may be damaged and require replacement.
How to fix Quietside Air Conditioner indoor fan motor?
If the indoor fan motor in your Quietside Air Conditioner is burned, broken, or the heat protector has malfunctioned, replace the fan motor or the defective part.
General| Brand | Quietside |
|---|---|
| Model | QS12-VP115 |
| Category | Air Conditioner |
| Language | English |
Displays an image and listing for the indoor unit models QS09-VJ115 and QS12-VJ115.
Displays an image and listing for the outdoor unit models QS09-VP115 and QS12-VP115.
Identifies the specific model of the remote controller used with the unit.
Presents a detailed table of electrical, performance, and physical specifications for the unit models.
Illustrates compressor speed vs. current performance for cooling and heating modes.
Graphs showing how cooling and heating capacity change with outdoor temperature.
Displays noise levels for indoor and outdoor units at different fan speeds or compressor frequencies.
Provides cooling and heating performance data under rated frequency operating conditions.
Shows detailed measurements and diagrams for the indoor unit's physical size.
Presents diagrams and measurements for the outdoor unit, including a size table.
Shows the complete wiring schematic for the indoor and outdoor units.
Illustrates the printed circuit board layouts for both indoor and outdoor units.
Details the buttons and display icons on the remote control unit.
Provides in-depth explanations of various operating modes like cooling, dry, heating, and fan.
Offers step-by-step troubleshooting flowcharts for common operational issues.
Lists and explains various error codes displayed by the unit and their possible causes.
Details diagnostic procedures for critical system malfunctions and faults.
Provides an exploded diagram and a list of parts for the indoor unit.
Presents an exploded diagram and a list of parts for the outdoor unit.
Step-by-step instructions for removing parts of the indoor unit.
Step-by-step instructions for removing parts of the outdoor unit.
To Next Page
