RAB AL - User Manual

AL
TM
AREA LIGHT INSTALLATION INSTRUCTIONS
®
Page 1
Thank you for buying RAB lighting
xtures. Our aim is to design the
best quality products to get the job
done right. We’d like to hear your
comments. Call the Marketing
Department at 888-RAB-1000, or
email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. This product must be installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product and the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture.
MOUNTING wITH SLIPfITTER
The sliptter ts a 2 3/8” O.D. tenon. Place the
sliptter over the tenon and secure with the (2) Set
Screws on the side of the sliptter.
To adjust the angle of the xture:
a. Remove (2) Cover Plate Screws and the
Round Cover Plate.
b. Hold the top of xture, loosen the Locking Bolt
and swivel the xture.
c. Tighten the Locking Bolt and re-attach the
Round Cover Plate.
1.
2.
Locking
Bolt
Set Screws
Round Cover
Plate
Cover Plate
Screws
fIXED ARM
For full cutoff, mount arm oriented as shown below.
UP TILT fIXED ARM
For 6 degree up tilt, mount arm oriented as shown below.
POLE DRILLING DETAIL
For mounting to a pole not drilled at RAB.
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
RAB xture designs are protected under
U.S. and International Intellectual Property laws.
Patent pending.

Summary

Mounting Types and Methods

Fixed Arm Mounting

Describes mounting the fixture with a fixed arm for full cutoff orientation.

Up Tilt Fixed Arm Mounting

Describes mounting the fixture with a fixed arm for a 6-degree up tilt.

Mounting with Slipfitter

Instructions for attaching the fixture to a pole tenon using a slipfitter.

Pole Drilling Detail

Provides drilling specifications for mounting to a pole not pre-drilled.

Pole Mounting Configurations

Mounting (1) Fixture Directly to Pole

Details for fixed arm mounting a single fixture directly to a square steel pole.

Mounting (2) Fixtures at 180° Directly to Pole

Instructions for mounting two fixtures at 180 degrees directly to a pole.

Mounting (2) Fixtures at 90° Directly to Pole

Instructions for mounting two fixtures at 90 degrees directly to a pole.

Mounting (3) Fixtures Directly to Pole

Details for mounting three fixtures directly to a pole.

Mounting (4) Fixtures Directly to Pole

Details for mounting four fixtures directly to a pole.

BTA Adaptor Mounting Configurations

Mounting (1) Fixture to BTA Adaptor

Steps for mounting a single fixture to RAB's pole top adaptor.

Mounting (2) Fixtures at 180° to BTA Adaptor

Instructions for mounting two fixtures at 180 degrees using a BTA adaptor.

Mounting (2) Fixtures at 90° to BTA Adaptor

Instructions for mounting two fixtures at 90 degrees using a BTA adaptor.

Mounting (3) Fixtures to BTA Adaptor

Details for mounting three fixtures to a BTA adaptor.

Mounting (4) Fixtures to BTA Adaptor

Details for mounting four fixtures to a BTA adaptor.

Lamp Installation, Wiring, and Maintenance

Lamp Installation

Procedure for safely installing the correct lamp into the fixture.

Wiring Instructions

Guidance for connecting the fixture's electrical leads for 277V operation.

Troubleshooting

Common issues and checks for fixture operation and installation problems.

Cleaning & Maintenance

Recommendations for cleaning the fixture and maintaining light output.

Replacement Parts

List of available accessories and replacement parts for the fixture.

RAB AL Specifications

General

Category	Flood Light
Color Temperature	5000K
Beam Angle	120°
IP Rating	IP65
Input Voltage	120-277V
Lifespan	50, 000 hours
Material	Aluminum