RadioMaster R168

产品特性
通道个数：16通道
频率范围：2400-2483.5Mhz
信号格式：D16
供电范围：4.5-8.4V
输出格式：PWM、SBUS
支持回传：S.port、RSSI输出、VBAT（最高18V电压检测）
控制距离：大于1km
失控保护：CUSTOM（全通道自定义）、HOLD（失控保持）、NO PULSES（无脉冲）
天线长度：约15cm
尺 寸：40*26*16毫米
重 量：10克
对频方法
1. 接收机按住BIND按钮，同时接通电源，接收机LED红绿灯同时常亮，等待对频
2. 遥控器多协议高频头选择D16协议，并按下[BIND]选项，接收机红灯闪烁，表示对频成功
3. 遥控器退出[BIND]模式，接收机需重新通电，此时接收机绿灯常亮，对频成功
对频时遥控器弹出模式选单
Ch1-8 Telem ON：接收机PWM接口输出1-8通道信号，回传开启
Ch1-8 Telem OFF：接收机PWM接口输出1-8通道信号，回传关闭
Ch9-16 Telem ON：接收机PWM接口输出9-16通道信号，回传开启
Ch1-16 Telem OFF：接收机PWM接口输出9-16通道信号，回传关闭
失控保护
接收机支持多种失控保护方式，可在遥控器
Failsafe mode中选择相应的设置，自定义失控保护
R168接收机用户指南
Failsafe mode失控保护设置选项说明
1. Not set：未设置失控保护，遥控器开机会弹出相应提示，提
醒您设置失控保护
2. Hold：失控保持，保持失控前最后一刻的通道输出
3. No pulses：无脉冲，接收机失控时关断所有通道输出信号
4. Receiver：接收机按钮设置，接收机短按BIND按钮小于1秒，
接收机LED绿灯闪烁两次，即保存当前遥控通道值，作为接收机
失控保护值
5. Custom：自定义，选择[Set]进入以下界面，可在此界面定义
每个通道值，选择最下方Channels=>Failsafe选项，即可将当前
设置发送到接收机，作为接收机失控保护值
Batt
S.port
RSSI
S.BUS
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
S
(Max 18V)
BIND
LED
2.4GHz
DC4.5-8.4V
R168
CH1
S
S
S
Batt
S.port
RSSI
S.BUS
CH2
CH3
CH4
CH5
CH6
CH7
CH8
8 CHANNEL RECEIVER

RadioMaster R168 Specifications

General

Type	Receiver
Channels	16
Telemetry	Yes
Frequency Range	2.4 GHz
Telemetry Power	100 mW
Signal Protocol	SBUS
Antenna	Dual

Summary

Product Features

Key Specifications

Lists channel count, frequency range, signal format, power, output, telemetry support, range, failsafe, antenna, size, and weight.

Binding Method

Binding Mode Options

Explains receiver PWM output and telemetry settings for different binding modes (Ch1-8/9-16 Telem ON/OFF).

Failsafe Protection

Failsafe Setting Options

Details the failsafe options: Not set, Hold, No pulses, Receiver, and Custom settings.

Voltage Telemetry

Discovering Telemetry Sensors

Instructions for scanning new sensors on the remote control's telemetry page.

Calibrating Voltage Sensor

Guide to adjusting the Ratio parameter for accurate battery voltage readings.

Receiver Specifications

Bind Method

Binding Mode Options Explained

Details receiver PWM output and telemetry settings for various binding modes.

Setting Fail-safe

Failsafe Setting Options

Describes failsafe modes: Not set, Hold, No pulses, Receiver, and Custom.

Battery Telemetry

Discovering Telemetry Sensors

Instructions for scanning new sensors on the radio's telemetry page.

Calibrating Voltage Sensor

Adjust the ratio parameter until displayed voltage matches actual battery voltage.

Frequency Fine Tuning

Frequency Fine Tuning Procedure

Steps to tune frequency for optimal range and stability by finding connection loss points.