RadioMaster R86

产品特性
通道个数：6通道
频率范围：2400-2483.5Mhz
供电范围：4.5-8.4V
信号格式：D8
输出格式：PWM
控制距离：大于1km
天线长度：15厘米
尺 寸：28*16.5*11毫米
重 量：4.8克
Receiver Specifications
Channels: 6
Frequency range: 2400-2483.5Mhz
Power input range: 4.5-8.4V
Signal format: D8
Output format: PWM
Range: more than 1km
Antenna length: 15cn
Size: 28*16.5*11mm
Weight: 4.8g
对频方法
1.接收机按住BIND按钮，同时接通电源，约等待3秒后接收机LED红灯常亮，等待对频
2.遥控器多协议高频头选择D8协议，并按下[BIND]选项，接收机红灯闪烁，表示对频成功
3.遥控器退出[BIND]模式，接收机需重新通电，此时接收机红灯常亮，对频成功
失控保护
1. 接收机通电10秒内，按一次BIND按钮，接收机将保存遥控器当前所有通道值，作为失控保值
2. 接收机通电10秒之后，BIND按钮功能将被停用，以防止飞行时误触更改失控保护设置
R86接收机用户指南
R86 Receiver User manual
Bind Method
Fail-safe Protection
1. Press and hold the BIND button on the receiver then connect power. After approximately 3
seconds, the receiver LED will be RED, the receiver is now in bind mode.
2. Select the D8 protocol for the multi-protocol menu of your remote control, and press the
[BIND] option, the red light of the receiver will flash indicating successful bind.
3. Exit bind mode on your remote control and disconnect power to the receiver then power the
receiver once more. The LED will now be solid RED indicated the bind is now done. If not
please repeat step 1 and 2.
1. Press the BIND button once within 10 seconds of the receiver being powered on, and the
receiver will save all the current channel values of the remote control as the fail-safe value.
2. 10 seconds after the receiver is powered on, the BIND button function will be disabled to
prevent accidental changes to to the fail-safe settings while preparing the model for flight.
CH1
CH1
CH2
CH2
CH3
CH3
CH4
CH4
CH5
CH5
CH6
CH6
S
BIND
LED
DC4.5-8.4V2.4GHz

RadioMaster R86 Specifications

General

Channels	6
Firmware	Upgradable
Telemetry power	100mw
Protocol	ACCESS
Compatibility	RadioMaster
Frequency Range	2.4GHz
Antenna connector	IPEX
Antenna	Dual

Summary

Product Specifications

Bind Method

Initiate Bind Mode

Press and hold the BIND button on the receiver, then connect power. Wait for the LED to turn solid RED.

Perform Bind Procedure

Select D8 protocol on remote and press BIND. Receiver LED will flash, indicating successful bind.

Confirm Bind Success

Exit bind mode, disconnect receiver power, then reconnect. LED should be solid RED.

Fail-safe Protection

Set Fail-safe Value

Within 10 seconds of powering on, press BIND to save current remote channel values as fail-safe.

Disable Fail-safe Setting

After 10 seconds, the BIND button function is disabled to prevent accidental changes.

Frequency Fine Tuning

Lower Frequency Value

Gradually decrease RF Freq. fine tune until signal is lost. Record this value (TUNE_MIN).

Raise Frequency Value

Gradually increase RF Freq. fine tune until signal is lost again. Record this value (TUNE_MAX).

Calculate Median Frequency

Calculate the median frequency by averaging TUNE_MIN and TUNE_MAX, then set it.