Rancilio classe 8 Use And Maintenance

62
8.5. Machines with TSC automatic system
(Fig.7) (only Mod. DE)
8.5.1 Heating Milk or a Drink (TSC)
● Immerse the wand in the drink
● Press button 6.2 on the keypad (Fig.7)
● The display will show the temperature of the
drink
● Press button 6.2 again to stop heating at the de-
sired temperature.
● Wait for the machine to stop automatically at the
programmed temperature.
8.5.2. Preparing Frothed Milk (TSC)
● Immerse the wand in a container containing at
least 250 cc of milk (the sensor must be at least 3
cm below the water level).
To obtain best results, use refrigerated milk (≤ 5°C)
- (≤ 41°F)
● Press button 6.1 on the keypad (Fig.7)
● The display shows the temperature of the milk.
● Press button 6.1 again to stop the machine at the
desired temperature and emulsion level.
● Wait for the machine to stop automatically at the
set temperature and level of froth.
8.6 Programming functions
8.6.1 Programming Panel (Mod.DE)
Use the first coffee keyboard with keys having the
following functions (Fig.9):
1° Button Enter programming
Keeping pressed for 8 sec. you enter
programming, then you have:
(Fig.10)
1° Button “+” To move to a higher level in the
programming menus. Or to
increase the value
2°Button “-” To move to a lower level in the
programming menus. Or to
decrease the value
3° Button “enter” To enter the programming
menu. Or to confirm entries
4° Button “esc” To quit the menu
Or to quit programming mode.
5° Button Key off.
When the dose of hot water is being delivered electro-
nically, delivery can be interrupted by pressing the
button 5B.
When purified water is used, these beverages often
assume a darker colour.
Should the user prefer a lighter coloured drink, draw
fresh water from an ordinary tap and proceed with the
heating phase as described in point 8.3.
8.7 Programming (Mod.DE)
By keeping START/STOP key pressed and switching
the machine off and on again, you will enter pro-
gramming.
8.7.1 Barman programming (Fig.12)
By keeping key 1 of keyboard 1 pressed for 8 seconds
you will enter programming.
By pressing “+” and “-” keys the following sub-menus
will be browsed:
Programming with the following sub-menus:
- Clock
- Set date
- Set time
- Date/time format
- Set timer
- Stand by timer
- Sunday
8.7.2.Clock
Sub-menu to set date and time and mode (24 hours
or English 12 hours and date with dd/mm/yy or
mm/dd/yy)
8.7.3 Set timer
Menu to set automatic switching on/off of the machine
as follows:
- select automatic or manual switching on (to enable
function or not)
- set switching on time for every day of the week
- set working hours
To browse from one menu to another press “+” or “-”,
to enter a sub-menu or to confirm a variation press
“enter”, to exit press “esc”.
The value that can be modified with “+” or “-” keys
is flashing.
8.7.4 Timer-cut-out (Fig.13)
If the machine is turned off by the program, by pres-
sing key 4 of keybord 1 at least for 3-4 seconds it will
turn on again and remain on until the following pro-
grammed stop or by pressing the same key again.
If the machine is turned on by the program, by pres-
sing key 4 of keybord 1 at least for 3-4 seconds it will
turn off again and remain off until the following pro-
grammed stop or by pressing the same key again.

Rancilio classe 8 Specifications

General

Brand	Rancilio
Model	classe 8
Category	Coffee Maker
Language	English