R&S ZNA26 - Page 1653

Annexes
R&S
®
ZNA
1653User Manual 1178.6462.02 ─ 20
5. Modify the value ShowroomSetup: set its value data to the full path of the recall
set. Use forward slashes as path separators, e.g. "C:/Documents and Settings/All
Users/Rohde-Schwarz/ZNA/RecallSets/ShowroomSet1.znxml".
After the analyzer is restarted or "Preset", the specified recall set is loaded.
12.5 ENA emulation commands
The following table lists the commands implemented/overwritten for the ENA remote
language.
ENA Emulation Command R&S ZNA Default Parser Command
CALCulate<Ch>:FSIMulator:SENDed:DEEM-
bed:PORT<Pt>[:TYPE] {USER|NONE}
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:DEEMbedding<PhyPt>:TNDefinition
CALCulate<Ch>:FSIMulator:SENDed:DEEM-
bed:PORT<Pt>:USER:FILename <string>
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:DEEMbedding<PhyPt>:PARameters:
DATA
CALCulate<Ch>:FSIMulator:SENDed:DEEM-
bed:STATe {ON|OFF|1|0}
n.a. (enabled channel-by-channel, port-by-port)
CALCulate{1..4}:FSIMulator:SENDed:PMCir-
cuit:STAT {ON|OFF|1|0}
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:EMBedding<PhyPt>[:STATe]
CALCulate{1..4}:FSIMulator:SENDed:PMCir-
cuit:PORT<Pt>[:TYPE] {NONE|PCSC|PCSL|PLPC|
PLSC|PLSL|SCPC|SCPL|SLPC|SLPL|USER}
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:EMBedding<PhyPt>:TNDefinition
CALCulate{1..4}:FSIMulator:SENDed:PMCir-
cuit:PORT<i>:PARameter:C <numeric>
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:EMBedding<PhyPt>:PARameters:
C<Cmp>
CALCulate{1..4}:FSIMulator:SENDed:PMCir-
cuit:PORT<i>:PARameter:G <numeric>
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:EMBedding<PhyPt>:PARameters:
G<Cmp>
CALCulate{1..4}:FSIMulator:SENDed:PMCir-
cuit:PORT<i>:PARameter:L <numeric>
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:EMBedding<PhyPt>:PARameters:
L<Cmp>
CALCulate{1..4}:FSIMulator:SENDed:PMCir-
cuit:PORT<i>:PARameter:R <numeric>
CALCulate<Ch>:TRANsform:VNETworks:
SENDed:EMBedding<PhyPt>:PARameters:
R<Cmp>
CALCulate{1..4}:FSIMulator:SENDed:ZCONver-
sion:STATe {ON|OFF|1|0}
[SENSe<Ch>:]LPORt<LogPt>:ZDEFault[:
STATe]
CALCulate{1..4}:FSIMulator:SENDed:ZCONver-
sion:PORT<i>:Z0[:R] <numeric>
[SENSe<Ch>:]PORT<PhyPt>:ZREFerence
CALCulate<Ch>:FSIMulator:STATe {ON|OFF|1|0} n.a. (enabled channel-by-channel, port-by-port)
CALCulate{1...4}[:SELected]:DATA:FDATa?
CALCulate{1...4}[:SELected]:DATA:SDATa?
CALCulate{1...4}[:SELected]:DATA:FMEMory?
CALCulate<Chn>:DATA
ENA emulation commands