Raven SmarTrax User Manual (English)

Other manuals for Raven SmarTrax

Calibration And Operation Manual156 pages

Calibration & Operation Manual58 pages

Operation Manual73 pages

Installation Guide40 pages

Installation Manual59 pages

Questions and Answers:

K
Kimberly GrahamSep 1, 2025
What does 'VALID POINTS LOW' mean on Raven SmarTrax and how can I fix it?
- H
  hreidSep 1, 2025
  If you're experiencing a 'VALID POINTS LOW' error with your Raven Farm Equipment, verify that the SmarTrax hydraulic hose, fitting, and valve connections are secure and no leaks are present. Also, verify that harness cable connections are correct and securely installed and check the steering linkages to ensure they are connected securely and meet the machine manufacturer’s factory specifications.
S
Sharon SantanaAug 25, 2025
Why does Raven SmarTrax machine consistently drive to the left or right of the guidance line?
- E
  Ernest MooreAug 25, 2025
  If your Raven Farm Equipment machine consistently drives to the left or right of the guidance line, recalibrate the yaw sensor to zero while the machine is stationary and reset the SPS/WAS center calibration. Lower the appropriate PWM Min value until the front wheels steer very slowly manually and with minimum buttons. Increase the LA Aggressiveness and OL Sensitivity settings.
S
sarahdanielsAug 25, 2025
What does 'No Cal' mean on Raven Farm Equipment and how do I fix it?
- D
  David SanchezAug 26, 2025
  If your Raven Farm Equipment displays 'No Cal', calibrate the SmarTrax system using the calibration wizard.
J
John CurtisSep 6, 2025
What does '3D Cold' mean on Raven Farm Equipment and how do I fix it?
- T
  Thomas HenrySep 6, 2025
  If your Raven Farm Equipment displays '3D Cold', recalibrate terrain compensation.
A
Aaron HooverSep 3, 2025
What does 'No GGA' mean on Raven SmarTrax and how do I fix it?
- C
  Cassandra ShawSep 3, 2025
  If your Raven Farm Equipment displays 'No GGA' or 'No VTG', check the receiver settings. The recommended setting is 10Hz.
L
Lisa ClarkAug 29, 2025
What to do if Raven SmarTrax wheels turn the wrong way when the steering wheel is turned?
- R
  Ryan JamesAug 29, 2025
  If the Raven Farm Equipment wheels turn the wrong way when the steering wheel is turned, reverse the left and right steering hoses on the machine’s steering orbital.
B
Brandon EspinozaAug 29, 2025
What causes Raven SmarTrax Farm Equipment to display 'Hyd Stuck' or 'HYDRAULICS_STUCK' and how to fix it?
- S
  Stacy EdwardsAug 30, 2025
  To resolve the Raven Farm Equipment 'Hyd Stuck' or 'HYDRAULICS_STUCK' error, check all valve hydraulic and electrical connections. Also, check the SPS/WAS sensor and connections. If the problem persists, replace the node.
J
Jacob ClarkSep 8, 2025
What does 'Vlve Flt' mean on Raven SmarTrax Farm Equipment and how do I fix it?
- D
  Daniel StaffordSep 8, 2025
  To address the 'Vlve Flt' error on your Raven Farm Equipment, verify the proper software version is installed on the machine’s ISO CANbus and that the system is connected to a Raven-supported, ISO-compatible valve.
O
omartinAug 27, 2025
What to do if I have a 'Guide Com' error on Raven Farm Equipment?
- B
  bankskyleAug 27, 2025
  If you're experiencing a 'Guide Com' error on your Raven Farm Equipment, it means guidance points are no longer being received by SmarTrax. Verify connections between SmarTrax and the field computer. If you are using Viper Pro, verify that the “Send Guidance Message” option is on the Lightbar Setup screen.
S
Shelby RosalesAug 27, 2025
Why does my Raven Farm Equipment skip or overlap in the field?
- A
  Angela ShepardAug 27, 2025
  If your Raven Farm Equipment consistently skips or overlaps in the field, the antenna position entered in the field computer does not correlate with the position on the roof. Physically re-measure the antenna height and offset and adjust the values in the field computer.