EasyManua.ls Logo

Raven SmarTrax - User Manual

Default Icon
156 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
P/N 016-0171-277 Rev. L 03/18 E30676
Copyright 2009, 2010, 2011, 2012, 2013, 2017, 2018
SmarTrax™ Calibration and
Operation Manual

Table of Contents

Other manuals for Raven SmarTrax

Preview: Operation Manual
Operation Manual73 pages
Preview: Calibration & Operation Manual
Calibration & Operation Manual58 pages
Preview: Installation Guide
Installation Guide40 pages
Preview: Installation Manual
Installation Manual59 pages
Preview: Supplement Installation Manual
Supplement Installation Manual22 pages

Questions and Answers

  • K
    Kimberly GrahamSep 1, 2025
    What does 'VALID POINTS LOW' mean on Raven SmarTrax and how can I fix it?
    • H
      hreidSep 1, 2025
      If you're experiencing a 'VALID POINTS LOW' error with your Raven Farm Equipment, verify that the SmarTrax hydraulic hose, fitting, and valve connections are secure and no leaks are present. Also, verify that harness cable connections are correct and securely installed and check the steering linkages to ensure they are connected securely and meet the machine manufacturer’s factory specifications.
  • S
    Sharon SantanaAug 25, 2025
    Why does Raven SmarTrax machine consistently drive to the left or right of the guidance line?
    • E
      Ernest MooreAug 25, 2025
      If your Raven Farm Equipment machine consistently drives to the left or right of the guidance line, recalibrate the yaw sensor to zero while the machine is stationary and reset the SPS/WAS center calibration. Lower the appropriate PWM Min value until the front wheels steer very slowly manually and with minimum buttons. Increase the LA Aggressiveness and OL Sensitivity settings.
  • E
    eugene39Sep 16, 2025
    What does 'Low Stats' mean on Raven Farm Equipment?
    • P
      Patricia Friedman DDSSep 16, 2025
      A 'Low Stats' message on Raven Farm Equipment means that the GPS receiver is not receiving signal from enough satellites. Wait a few minutes to see if more satellites are found.
  • M
    Meghan SchroederSep 23, 2025
    What does 'VALID POINTS LOW' mean on Raven Farm Equipment?
    • K
      katherine33Sep 23, 2025
      If you're seeing a 'VALID POINTS LOW' error on your Raven Farm Equipment, not enough valid measurements are being received by the steering control device during calibration. Verify that the SmarTrax hydraulic hose, fitting, and valve connections are secure and no leaks are present. Verify that harness cable connections are correct and securely installed. Check the steering linkages to ensure they are connected securely and meet the machine manufacturer’s factory specifications.
  • C
    Christine BowmanSep 12, 2025
    How to resolve 'No A-B Msg' error on Raven Farm Equipment?
    • D
      Donna RichardsSep 12, 2025
      If you're getting a 'No A-B Msg' error on your Raven Farm Equipment, it indicates that the A-B line has not been set on the field computer or there is no communication from the field computer. To fix this, set the A-B line in the field computer. Also, verify the cabling is correct and secure, and ensure the “Send Guidance” message is selected.
  • A
    Aaron HooverSep 3, 2025
    What does 'No GGA' mean on Raven SmarTrax and how do I fix it?
    • C
      Cassandra ShawSep 3, 2025
      If your Raven Farm Equipment displays 'No GGA' or 'No VTG', check the receiver settings. The recommended setting is 10Hz.
  • L
    Lisa ClarkAug 29, 2025
    What to do if Raven SmarTrax wheels turn the wrong way when the steering wheel is turned?
    • R
      Ryan JamesAug 29, 2025
      If the Raven Farm Equipment wheels turn the wrong way when the steering wheel is turned, reverse the left and right steering hoses on the machine’s steering orbital.
  • M
    Michael KennedySep 18, 2025
    What does 'Swath Jmp' mean on Raven Farm Equipment?
    • D
      David RivasSep 22, 2025
      If you're seeing a 'Swath Jmp' error on your Raven Farm Equipment, it indicates that the guidance points being sent from the field computer have jumped swaths, causing the system to disengage. Verify the guidance line on the field computer is not switching between lines.
  • W
    williamsonmatthewSep 23, 2025
    What does 'XDucer Er' mean on Raven Farm Equipment and how can I resolve it?
    • K
      Krista MackSep 23, 2025
      If you're seeing an 'XDucer Er' error on your Raven Farm Equipment, a problem with the pressure transducer or cabling has been detected. Verify the PSI values on the System Diagnostics screen. Verify pressure transducer connection and cabling.
  • O
    omartinAug 27, 2025
    What to do if I have a 'Guide Com' error on Raven Farm Equipment?
    • B
      bankskyleAug 27, 2025
      If you're experiencing a 'Guide Com' error on your Raven Farm Equipment, it means guidance points are no longer being received by SmarTrax. Verify connections between SmarTrax and the field computer. If you are using Viper Pro, verify that the “Send Guidance Message” option is on the Lightbar Setup screen.

Summary

Important Safety Information

Hydraulic Safety

Guidelines for working safely with the hydraulic system, including protective equipment and fluid handling.

Electrical Safety

Precautions for electrical connections, polarity, and voltage requirements for the SmarTrax system.

Introduction

Recommendations

Best practices for installing and operating the SmarTrax system for the first time.

Antenna Installation

Details on positioning the GPS antenna for optimal system performance and accuracy.

CR7 Calibration and Operation

Buttons and Definitions

Explains common status and mode information displayed on the CR7 during SmarTrax operation.

Machine Configuration

Steps for setting up machine profiles and configuring machine-specific settings in the CR7.

Calibrate SmarTrax System

Overview of the SmarTrax calibration wizard and initial setup steps for the system.

System Adjustments

Information on tuning system performance and adjusting parameters like Line Acquisition and Sensitivity.

Viper 4;4+ Calibration and Operation

Widget and Button Definitions

Defines common status icons and buttons used on the Viper 4/4+ display for SmarTrax.

GPS Configuration

Steps to configure GPS settings and ensure proper communication for the SmarTrax system.

Machine Configuration

Process for selecting machine types and setting up profiles for SmarTrax operation on Viper 4/4+.

Calibrate SmarTrax System

Detailed procedure for calibrating the SmarTrax system using the setup wizard.

System Adjustments

Guidelines for fine-tuning SmarTrax performance, including LA and OL modes.

Viper Pro Calibration and Operation

Software Compatibility

Requirements for Viper Pro software and SmarTrax node software versions for compatibility.

SmarTrax Status Display

How to interpret system status messages displayed on the Viper Pro screen.

Machine Configuration

Setting up machine profiles and specific configurations for SmarTrax on Viper Pro.

Calibrate SmarTrax System

Step-by-step guide to calibrating the SmarTrax system with the Viper Pro.

System Adjustments

Tuning SmarTrax parameters like LA and OL sensitivity for optimal field operation.

Envizio Pro and Cruizer II Calibration and Operation

Software Compatibility

Specifies required software versions for Envizio Pro/Cruizer II and SmarTrax node.

SmarTrax Status Display

Interpreting SmarTrax system status icons on the Envizio Pro/Cruizer II display.

Machine Configuration

Steps to configure machine profiles and specific settings for SmarTrax with Envizio Pro/Cruizer II.

Calibrate SmarTrax System

Guide for calibrating the SmarTrax system when used with Envizio Pro or Cruizer II.

System Adjustments

Adjusting SmarTrax settings like LA and OL sensitivity for optimal field operation.

Troubleshooting

Node

Explains SmarTrax CAN control node LEDs for diagnosing system issues.

Error Messages

Lists common SmarTrax error messages, their causes, and corrective actions.

System Diagrams

SmarTrax 3 D with Envizio Pro or Viper Pro and Phoenix 300

Provides a wiring diagram for the SmarTrax 3D system with specific field computers.

Raven SmarTrax Specifications

General IconGeneral
BrandRaven
ModelSmarTrax
CategoryFarm Equipment
LanguageEnglish

Related product manuals