Why is the steering wheel hard to turn when disengaging Raven Farm Equipment SmarTrax?
If the steering wheel is difficult to turn when attempting to disengage SmarTrax, the pressure switch knob or disengage setting is set incorrectly. Turn the knob out on the pressure switch and/or decrease the disengage setting.
What does 'VALID POINTS LOW' mean on Raven SmarTrax and how can I fix it?
If you're experiencing a 'VALID POINTS LOW' error with your Raven Farm Equipment, verify that the SmarTrax hydraulic hose, fitting, and valve connections are secure and no leaks are present. Also, verify that harness cable connections are correct and securely installed and check the steering linkages to ensure they are connected securely and meet the machine manufacturer’s factory specifications.
What to do if I have a 'Guide Com' error on Raven Farm Equipment?
If you're experiencing a 'Guide Com' error on your Raven Farm Equipment, it means guidance points are no longer being received by SmarTrax. Verify connections between SmarTrax and the field computer. If you are using Viper Pro, verify that the “Send Guidance Message” option is on the Lightbar Setup screen.
What does 'High HDOP' mean on Raven Farm Equipment?
A 'High HDOP' message on Raven Farm Equipment means that insufficient GPS signal is being received. Wait a few minutes to see if signal improves.
What does 'Too FAST' mean on Raven Farm Equipment and how to resolve it?
The 'Too FAST' error on Raven Farm Equipment indicates that the vehicle speed is above 29 mph [45 km/h] or has been above 27 mph for more than 5 seconds, and SmarTrax has been disengaged. To resolve this, decrease the vehicle speed and re-engage the SmarTrax system.
What does 'No GGA' mean on Raven SmarTrax and how do I fix it?
If your Raven Farm Equipment displays 'No GGA' or 'No VTG', check the receiver settings. The recommended setting is 10Hz.
What does '3D Cold' mean on Raven Farm Equipment and how do I fix it?
If your Raven Farm Equipment displays '3D Cold', recalibrate terrain compensation.
How to resolve 'No A-B Msg' error on Raven Farm Equipment?
If you're getting a 'No A-B Msg' error on your Raven Farm Equipment, it indicates that the A-B line has not been set on the field computer or there is no communication from the field computer. To fix this, set the A-B line in the field computer. Also, verify the cabling is correct and secure, and ensure the “Send Guidance” message is selected.
What does 'Low Stats' mean on Raven Farm Equipment?
A 'Low Stats' message on Raven Farm Equipment means that the GPS receiver is not receiving signal from enough satellites. Wait a few minutes to see if more satellites are found.
What does 'No Cal' mean on Raven Farm Equipment and how do I fix it?
If your Raven Farm Equipment displays 'No Cal', calibrate the SmarTrax system using the calibration wizard.
Guidelines for working safely with the hydraulic system, including protective equipment and fluid handling.
Precautions for electrical connections, polarity, and voltage requirements for the SmarTrax system.
Best practices for installing and operating the SmarTrax system for the first time.
Details on positioning the GPS antenna for optimal system performance and accuracy.
Explains common status and mode information displayed on the CR7 during SmarTrax operation.
Steps for setting up machine profiles and configuring machine-specific settings in the CR7.
Overview of the SmarTrax calibration wizard and initial setup steps for the system.
Information on tuning system performance and adjusting parameters like Line Acquisition and Sensitivity.
Defines common status icons and buttons used on the Viper 4/4+ display for SmarTrax.
Steps to configure GPS settings and ensure proper communication for the SmarTrax system.
Process for selecting machine types and setting up profiles for SmarTrax operation on Viper 4/4+.
Detailed procedure for calibrating the SmarTrax system using the setup wizard.
Guidelines for fine-tuning SmarTrax performance, including LA and OL modes.
Requirements for Viper Pro software and SmarTrax node software versions for compatibility.
How to interpret system status messages displayed on the Viper Pro screen.
Setting up machine profiles and specific configurations for SmarTrax on Viper Pro.
Step-by-step guide to calibrating the SmarTrax system with the Viper Pro.
Tuning SmarTrax parameters like LA and OL sensitivity for optimal field operation.
Specifies required software versions for Envizio Pro/Cruizer II and SmarTrax node.
Interpreting SmarTrax system status icons on the Envizio Pro/Cruizer II display.
Steps to configure machine profiles and specific settings for SmarTrax with Envizio Pro/Cruizer II.
Guide for calibrating the SmarTrax system when used with Envizio Pro or Cruizer II.
Adjusting SmarTrax settings like LA and OL sensitivity for optimal field operation.
Explains SmarTrax CAN control node LEDs for diagnosing system issues.
Lists common SmarTrax error messages, their causes, and corrective actions.
Provides a wiring diagram for the SmarTrax 3D system with specific field computers.
General| Brand | Raven |
|---|---|
| Model | SmarTrax |
| Category | Farm Equipment |
| Language | English |
To Next Page