What to do if I have a 'Guide Com' error on Raven Farm Equipment?
If you're experiencing a 'Guide Com' error on your Raven Farm Equipment, it means guidance points are no longer being received by SmarTrax. Verify connections between SmarTrax and the field computer. If you are using Viper Pro, verify that the “Send Guidance Message” option is on the Lightbar Setup screen.
How to resolve 'No A-B Msg' error on Raven Farm Equipment?
If you're getting a 'No A-B Msg' error on your Raven Farm Equipment, it indicates that the A-B line has not been set on the field computer or there is no communication from the field computer. To fix this, set the A-B line in the field computer. Also, verify the cabling is correct and secure, and ensure the “Send Guidance” message is selected.
Why is the hydraulic disengage switch or transducer not detected during calibration of my Raven Farm Equipment?
If the hydraulic disengage switch or transducer is not detected during calibration, the priority valve in the open center valve may be stuck. Consider replacing the cartridge or the open center valve. The cable connection(s) to the disengage switch may also be improperly connected or loose, so verify disengage switch connections are correct and secure. Additionally, the cable connection to the transducer may be improperly connected or loose, so verify the connection to the transducer is correct and secure.
What does 'Cal' mean on Raven Farm Equipment?
If you're seeing a 'Cal' message on your Raven Farm Equipment, the /WAS has been detected but not calibrated. Calibrate the /WAS.
What does 'Road Mode' mean on Raven Farm Equipment?
If you see a 'Road Mode' message on your Raven Farm Equipment, the roading switch is in the off position. Switch the roading switch to the on position.
What causes 'Hyd Stuck' or 'HYDRAULICS_STUCK' error on Raven Farm Equipment?
If you're seeing a 'Hyd Stuck' or 'HYDRAULICS_STUCK' error on your Raven Farm Equipment, it means insufficient or no wheel movement is detected by the field computer. Check all valve hydraulic connections and all valve electrical connections. Also, check the /WAS sensor and connections.
What does '3D Hot' mean on Raven Farm Equipment?
If you see a '3D Hot' message on your Raven Farm Equipment, it means the system is significantly warmer than when terrain compensation was calibrated. Recalibrate terrain compensation.
What does '3D Cold' mean on Raven Farm Equipment?
If you see a '3D Cold' message on your Raven Farm Equipment, it means the system is significantly cooler than when terrain compensation was calibrated. Recalibrate terrain compensation.
What to do if Raven SmarTrax wheels turn the wrong way when the steering wheel is turned?
If the Raven Farm Equipment wheels turn the wrong way when the steering wheel is turned, reverse the left and right steering hoses on the machine’s steering orbital.
What causes Raven SmarTrax Farm Equipment to display 'Hyd Stuck' or 'HYDRAULICS_STUCK' and how to fix it?
To resolve the Raven Farm Equipment 'Hyd Stuck' or 'HYDRAULICS_STUCK' error, check all valve hydraulic and electrical connections. Also, check the SPS/WAS sensor and connections. If the problem persists, replace the node.
General| Brand | Raven |
|---|---|
| Model | SmarTrax |
| Category | Farm Equipment |
| Language | English |
Guidelines for working safely with the hydraulic system, including protective equipment and fluid handling.
Precautions for electrical connections, polarity, and voltage requirements for the SmarTrax system.
Best practices for installing and operating the SmarTrax system for the first time.
Details on positioning the GPS antenna for optimal system performance and accuracy.
Explains common status and mode information displayed on the CR7 during SmarTrax operation.
Steps for setting up machine profiles and configuring machine-specific settings in the CR7.
Overview of the SmarTrax calibration wizard and initial setup steps for the system.
Information on tuning system performance and adjusting parameters like Line Acquisition and Sensitivity.
Defines common status icons and buttons used on the Viper 4/4+ display for SmarTrax.
Steps to configure GPS settings and ensure proper communication for the SmarTrax system.
Process for selecting machine types and setting up profiles for SmarTrax operation on Viper 4/4+.
Detailed procedure for calibrating the SmarTrax system using the setup wizard.
Guidelines for fine-tuning SmarTrax performance, including LA and OL modes.
Requirements for Viper Pro software and SmarTrax node software versions for compatibility.
How to interpret system status messages displayed on the Viper Pro screen.
Setting up machine profiles and specific configurations for SmarTrax on Viper Pro.
Step-by-step guide to calibrating the SmarTrax system with the Viper Pro.
Tuning SmarTrax parameters like LA and OL sensitivity for optimal field operation.
Specifies required software versions for Envizio Pro/Cruizer II and SmarTrax node.
Interpreting SmarTrax system status icons on the Envizio Pro/Cruizer II display.
Steps to configure machine profiles and specific settings for SmarTrax with Envizio Pro/Cruizer II.
Guide for calibrating the SmarTrax system when used with Envizio Pro or Cruizer II.
Adjusting SmarTrax settings like LA and OL sensitivity for optimal field operation.
Explains SmarTrax CAN control node LEDs for diagnosing system issues.
Lists common SmarTrax error messages, their causes, and corrective actions.
Provides a wiring diagram for the SmarTrax 3D system with specific field computers.
To Next Page